background image

Declaration of Conformity

NASA Marine Ltd declare this product is in compliance with the essential requirements of 
R&TTE directive 1995/5/EC.
The original Declaration of Conformity certificate can be requested at [email protected]

THIS PRODUCT IS INTENDED FOR USE ONLY ON NON SOLAS VESSELS

 

IMPORTANT READ THIS BEFORE

UNPACKING INSTRUMENT

LIMITED WARRANTY

Prior to unpacking this instrument read and fully understand the installation instructions. 
Only proceed with the installation if you are competent to do so. Nasa Marine Ltd. will 
not accept any responsibility for injury or damage caused by, during or as a result of 
the installation of this product. Any piece of equipment can fail due to a number of 
causes. Do not install this equipment if it is the only source of information and its failure 
could result in injury or death. Instead return the instrument to your retailer for full credit. 
Remember this equipment is an aid to navigation and not a substitute for proper 
seamanship. This instrument is used at your own risk, use it prudently and check its 
operation from time to time against other data. Inspect the installation from time to time 
and seek advice if any part thereof is not fully seaworthy.

Nasa Marine Ltd. warrants this instrument to be substantially free of defects in both 
materials and workmanship for a period of one year from the date of purchase. 
Nasa Marine Ltd. will at its discretion repair or replace any components which fail in 
normal use within the warranty period. Such repairs or replacements will be made at 
no charge to the customer for parts and labour. The customer is however responsible 
for transport costs. This warranty excludes failures resulting from abuse, misuse, 
accident or unauthorised modifications or repairs. In no event shall Nasa Marine Ltd. 
be liable for incidental, special, indirect or consequential damages, whether resulting 
from the use, misuse, the inability to correctly use the instrument or from defects in 
the instrument. If any of the above terms are unacceptable to you then return the 
instrument unopened and unused to your retailer for full credit.

Name

Address

Dealer Name

Address

Date of Purchase

Proof of purchase may be required for warranty claims.

Nasa Marine Ltd.

Boulton Road, Stevenage, Herts SG1 4QG England

Содержание BM-1 Compact















Отзывы: