Narex EPR 30-20, Инструкция по эксплуатации

Страница: 23 / 44

��
41. The chain saw may only be used in a com-
pletely assembled state. No protective devices
may be missing.
42. Switch the chain saw off immediately if you
notice any changes in the machine.
43. Always have a first-aid kit fulfilling DIN 13164
at hand in case of accidents.
44. If the chain saw comes into contact with
earth, stones, nails or other foreign objects,
withdraw the plug immediately and check the
chain as well as the bar.
45. Ensure that no chain oil penetrates into the
earth or sewage.
Always place the chain saw on something
that will absorb any oil dripping from the bar
or chain.
D) Warning to the danger of recoil
(“kickback”)
46. Attention: If the tip of the bar contacts
a hard object while the motor is running,
the saw may recoil dangerously. In recoil-
ing, the chain saw is flung upwards at high speed
towards the person holding the chain saw.
47. Do not touch wood or branches with the bar
tip.
48. If possible, use a stand.
49. Always keep an eye on the bar tip.
50. Only place a running saw on the object to be
cut. Never start the machine while the chain
rests on something.
51. So called piercing cuts with the bar tip may
only be carried out by trained personnel.
E) Instructions on safe working
techniques
52. Before starting to work ensure that there is
sufficient light.
53. Always maintain a normal body posture when
operating the device. Always keep your balance.
54. Do not work with your body bent forwards.
55. Ensure that you are standing securely and
do not work on snow, ice or newly-barked wood.
Danger of slipping!
56. Working on ladders, scaffoldings or trees is
forbidden.
57. Do not use chain saw above shoulder height.
58. Use the chain saw only to cut wood. It is
absolutely forebidden to cut plastics or minerals
(gas concrete).
59. Ensure that the wood cannot twist while it is
being cut.
60. Never climb on a tree to cut wood.
61. Watch out for splintering wood. While you
are sawing you may be injured by flying wood
chips.
62. Do not use the chain saw to lever or move
the wood.
63. Only cut with the lower section of the saw.
The saw will be repulsed towards you if you try
and cut with the upper section of the saw.
64. Ensure that the wood is free of stones, nails
or other foreign objects.
65. We recommend that first-time users are
instructed practically as to the correct use of the
chain saw and the required personal safety
equipment by an experienced operator; the
cutting of round wood or logs should be trained
on a log stand or similar rack-type device first.
66. Keep the running chain saw from touching
the ground or wire fences. Do not cut thin wood
or timber that is already sawn into small pieces.
Starting up
Make sure the information on the factory tag
corresponds with the actual voltage of the power
source.
Make sure the socket plug type is compatible
with the type of socket.
The tools designed for 230 V can be connected
also to 220/240 V.
1. Filling the oil tank
(Fig. 1)
The chain saw must never be operated without
sufficient oil on the chain as this could cause
damage to the chain, blade or motor. No claims
for guarantee can be accepted if damage occurs
when the device is being operated without chain
oil.
Please use only biologically-based chainsaw oil,
i.e. oil which is 100% biologically decomposable.
Biological chainsaw oil should be available every-
where at your local specialist dealer. Do not use
old oil. This will damage the chainsaw and will
also lead to loss of the guarantee.
�
Before filling the oil tank, pull out the mains
plug.
�
Open the twist cap and place safely aside so
that the sealing ring in the tank cap does not
get lost.
�
Fill approx. 200 ml oil into the tank using a
funnel and screw on the tank cap tightly once
more.
�
The oil level can be seen in the inspection
window (Fig. 2). If you plan not to use the