Information about noise level and
vibrations
The values have been measured in conformity with
EN 60745.
Acoustic pressure level L
pA
= 52 dB (A).
Acoustic power level L
wA
= 68 dB (A).
In accuracy of measurements K = 3 dB (A).
The weighted value of vibrations affecting hands and arms
a
h
= 0.4 m.s
-2
.
In accuracy of measurements K = 1.5 m.s
-2
.
The emission values specified (vibration, noise) were meas-
ured in accordance with the test conditions stipulated in
EN 60745 and are intended for machine comparisons. They
are also used for making preliminary estimates regarding
vibration and noise loads during operation.
The emission values specified refer to the main applications
for which the power tool is used. If the electric power tool is
used for other applications, with other tools or is not main-
tained sufficiently prior to operation, however, the vibration
and noise load may be higher when the tool is used.
Take into account any machine idling times and downtimes
to estimate these values more accurately for a specified time
period. This may significantly reduce the load during the
machine operating period.
Use
AS 37-Li Cordless screwdriver is intended for screwing bolts
into soft, wooden-based construction materials and plastic
materials, in extreme cases even into metals.
The user is solely responsible for other than the intended
use.
Instructions for battery charging
1. The power tool can be charged only with the supplied
USB cable.
2. USB cable can be connected to any charging USB port.
(PC, cell phone charger etc.)
3. Allowable charging output is 5V/0.5A. The charging time
depends on the charger performance.
4. After the power tool has been fully charged, first
disconnect the USB cable from power supply and then
from the power tool itself.
The colour of the LED indicator by the charging
status:
Operation
Screws loosening
1. Start to loosen the screw in the same manner as with the
standard manual screwdriver.
2. Then press and hold button for loosening
▼
.
Screws tightening
1. Press and hold button for tightening
▲
.
2. Tighten the screw in the same manner as with the
standard manual screwdriver.
Maintenance and service
Instructions for device cleaning
Clean the external plastic parts by a wet rag and mild
detergent. Though these parts are made of the materials
resistant to solvents,
NEVER
use any solvent.
Attention! With respect to protection from el. shock and
preservation of the class of protection, all maintenance and
service operations requesting jig saw case removal must be
performed by the authorized service centre only!
The current list of authorized service centres can be found at
our website
www.narex.cz
, section
“Service centres”
.
Accessories
The accessories recommended for use with this device are
available commercially in the shops with hand el. tools.
Storage
Packed appliance may be stored in dry, unheated storage
place with temperature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage
place with temperature not lower than +5 °C with exclusion
of all sudden temperature changes.
Environmental protection
Power tools, accessories and packaging should be sorted for
environmental-friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste
electrical and electronic equipment and its incorporation
into national law, power tools that are no longer suitable
for must be separately collected and sent for recovery in an
environmental-friendly manner.
Warranty
Our equipment is under warranty for at least 12 months
with regard to material or production faults in accordance
with national legislation. In the EU countries, the warranty
period for exclusively private use is 24 months (an invoice or
delivery note is required as proof of purchase).
Damage resulting from, in particular, normal wear and
tear, overloading, improper handling, or caused by the user
or other damage caused by not following the operating
instructions, or any fault acknowledged at the time of
purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment has
not been dismantled before being sent back to the suppliers
or to an authorised NAREX customer support workshop.
Store the operating instructions, safety notes, spare parts
list and proof of purchase in a safe place. In addition, the
manufacturer’s current warranty conditions apply.
Note
Due to continuous research and development work, we
reserve the right to make changes to the technical content
of this documentation.
Certificate of Conformity
We declare that the device meets requirements of the
following standards and directives.
Safety:
EN 60745-1; EN 60745-2-1
Directive 2006/42/EC
RoHS:
Directive 2011/65/EU
Place of storage of the technical documentation:
Narex s.r.o., Chelčického 1932, 470 01 Česká Lípa,
Czech Republic
2017
Narex s.r.o.
Chelčického 1932
Maciej Stajkowski
470 01 Česká Lípa
CEO of the company
November 1, 2017
●
Red
Charging
●
Green
Fully charged
Safety instructions for battery
New batteries:
During the first charging cycles, the capacity of new
batteries may appear lower than the provided value. The
reason behind this is that the chemical composition has not
been activated yet. However, this is only a temporary state
which gets stabilized after several charging cycles.
• Use exclusively original battery supplied with the power
tool. Using different battery may result in the explosion
of the battery and/or personal injury.
• Do not dismantle the battery.
• Do not store the power tool in places where temperature
rises above 40°C.
• Charge the power tool in places with the ambient
temperature range between from 4°C to 40°C.
• Handle the battery carefully to prevent short-circuiting
its terminals. It may result in explosion or fire.
• Do not light the battery. It may result in fire or leakage of
liquids.
• There is a risk of leakage from battery under extreme
load or temperature conditions.
• In case the liquid leaks out and comes into contact with
your skin, wash the affected area with soap and plenty
of water. In case the liquid comes into contact with eyes,
rinse them with plenty of water and immediately seek
medical advice.
• It is recommended to cover the battery terminals with
insulating tape when disposing of the power tool. Please
consult your local authority on the right way to dispose
of the power tool equipped with a Li-ion battery.
• Do not dispose of the power tool in a dustbin, fire or
water.
• Dismantling or opening the external case could result in
damage.
Note about Li-Ion batteries
• This type of batteries does not suffer from memory effect
thus allowing to be charged in any state. If you remove
batteries from the charger prematurely, it does not result
in any damage.
• Li-Ion batteries are equipped with over-discharge
protection. In case of potential drop (caused by overload
or discharge) below the observable limit, cells will be
disconnected by electronics. The device will still perform
then or will cease to work completely. You will have to
reduce the load or recharge the battery.
