Napoleon Tureen GD82NT-T Скачать руководство пользователя

Страница: 1 / 32

W415-0583 / D / 07.24.07

INSTALLATION AND

OPERATION INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada

•

(705)721-1212

•

fax(705)722-6031

www.napoleonfireplaces.com

•

[email protected]

INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.

GD82NT-T

NATURAL GAS

GD82PT-T

PROPANE

WARNING: If the information in these
instructions are not followed exactly, a fire
or explosion may result causing property
damage, personal injury or loss of life.

- Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do

not use any phone in your building.

Immediately call your gas supplier from

a neighbour’s phone. Follow the gas

supplier’s

instructions.

If you cannot reach your gas supplier,

call the fire department.

- Installation and service must be
performed by a qualified installer, service
agency or the supplier.

SAFETY INFORMATION

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

W415-0583 / D / 07.24.07

$10.00

Содержание Tureen GD82NT-T

































Результаты поиска

Содержание Tureen GD82NT-T

Отзывы:

Похожие инструкции для Tureen GD82NT-T

Бренды по названию

Популярные бренды

Napoleon Tureen GD82NT-T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Tureen GD82NT-T

Отзывы:

Похожие инструкции для Tureen GD82NT-T

Бренды по названию

Популярные бренды