Napoleon PRESTIGE PRO PRO825-3, Руководство пользователя

Страница: 97 / 141

16
EN
www.napoleon.com N415-0537CE-GB-DE Jul 13.20
CAUTION!
Check for abrasions, melting, cuts, and cracks in the hose. If any of these conditions
exist, do not use the gas grill. Have the part replaced by your Napoleon Grill dealer or qualified gas
installer.
Aluminum Castings : Clean castings periodically with warm soapy water. Aluminum will not rust, but high
temperatures and weathering can cause oxidation to occur on aluminum surfaces. This appears as white
spots on the castings. To refinish these areas, clean first and sand lightly with fine sandpaper. Wipe the
surface to remove any residue and paint with high temperature barbecue paint. Protect surrounding
areas from over-spray. Follow the manufacture’s directions for curing.
Replacement Screen S81006
3. Impaired ventilation of hot air from the grill - For the burners to function properly, hot air must have a
way to escape the grill. If the hot air is not allowed to escape, the burners can become deprived of oxygen
causing them to back-flash. If this occurs repeatedly, the ceramic could crack. Never cover more than 75%
of the cooking surface with solid metal (i.e., griddle or large pan).
4. Incorrect cleaning - Do not clean the ceramic tile with a wire brush. If debris is collecting on your burner,
light the burner and operate on high for 5 minutes with the lid open, allowing debris to burn off.
WARNING!
Always wear protective gloves when changing the halogen bulb in the internal lights
of your grill.
Lights : To replace the halogen bulb in your grill you must first remove the lens from the light housing. To
remove the lens from the housing, remove the Phillips screw securing the housing in place. Snap the lens
out of the housing (including the metal bracket). Do not touch the halogen bulb with your bare hands.
The oil from your fingertips will reduce the life of the bulb. With gloved hands gently pull the old bulb
from the socket and replace with the new bulb. Reinstall the lens, by snapping it back into the housing
and bend the tabs on the front of the housing back in to position.
1
2
3
!
!
Troubleshooting
Problem Possible Causes Solution
Low heat / Low flame when
valve turned to high.
For propane - improper lighting procedure
For natural gas - undersized supply line
For both gases - improper preheating.
Ensure lighting procedure is followed carefully. All
gas grill valves must be in the off position when
the tank valve is turned on. Turn tank on slowly to
allow pressure to equalize. See lighting instructions.
Pipe must be sized according to installation code.
Preheat grill with both main burners
on high for 10 to 15 minutes.
Excessive flare-ups/
uneven heat.
Sear plates installed incorrectly.
Improper preheating.
Excessive grease and ash build on
sear plates and in drip pan.
See assembly instructions.
Preheat grill with main burners on
high for 10 to 15 minutes.
Clean sear plates and drip pan regularly.
Do not line pan with aluminum foil.
Refer to cleaning instructions.
Burners burn with yellow
flame, accompanied
by the smell of gas.
Possible spider web or other debris in burner. Thoroughly clean burner by removing. See
general maintenance instructions.
Rear and Side burners will
not light with the igniter,
but will light with a match.
Dead battery / or installed incorrectly.
loose electrode wire or switch terminal wires.
Replace with heavy duty premium battery.
Check that electrode wire is firmly pushed
onto the terminal on the back of the igniter.
Check that the lead wires from the module
to the ignition switch (if equipped) are firmly
pushed onto their respective terminals.
Illumination and Side/Rear
burner ignition do not work
Electric Power is out
The grill is nor receiving electric power Check the power outage in your area
Ensure the grill is connected between the
wall and the power bar of the grill
Ensure the red indicator is ON in the control box
Check if the fuse on the wire in the
cabinet is broken or not
Main burner will not light
with the igniter, but will
light with a match.
Jet-fire outlet is dirty or clogged. Clean jet-fire outlet with a soft bristle brush.
Humming regulator. Normal occurrence on hot days. This is not a defect. It is caused by internal
vibrations in the regulator and does not affect
the performance or safety of the gas grill.
Humming regulators will not be replaced.
Burners will not cross
light each other.
Dirty or corroded cross light brackets Clean or replace as required.
“Paint” appears to be
peeling inside lid or hood.
Grease build-up on inside surfaces. This is not a defect. The finish on the lid and
hood is porcelain, and will not peel. The peeling
is caused by hardened grease, which dries into
paint-like shards, that flake off. Regular cleaning
will prevent this. See cleaning instructions.
Burner output on “high”
setting is too low. (Rumbling
noise and fluttering blue
flame at burner surface.)
lack of gas.
Supply hose is pinched.
Dirty or clogged orifice.
Spider webs or other matter in venturi tube.
Check gas level in propane cylinder.
Reposition supply hose as necessary.
Clean burner orifice.
Clean out venturi tube.