Napoleon Haliburton GDS28-1NE Скачать руководство пользователя

Страница: 40 / 54

W415-2339 / C / 02.08.21

maintenance

12.3 blower replacement

Blower replacement may be done through either the fi rebox or from the rear of the appliance. Using the rear panel

is recommended.

INSTALLATION THROUGH THE REAR PANEL :

FOR MODEL GDS28

•

Turn off the electrical power and the gas supply to the appliance.

•

Remove the two combustion air covers and gaskets held on with 4

screws each. Remove the rear panel held in place with 6 screws.

•

Remove the 2 screws holding the blower to its mounting plate.

Disconnect the two blower wires.

•

Replace the blower and reconnect the two wires. When replacing the rear

panel, ensure that the wires are neither pinched nor interfere with the blower

operation. Ensure that the combustion air cover

plates and gaskets are properly installed and sealed.

FOR MODEL GS28

•

Turn off the electrical power and the gas supply to

the appliance.

•

Remove the 8 screws securing the air intake

manifolds to the rear panel. Remove the rear panel

held in place with 6 screws.

•

Remove the 2 screws holding the blower to its

mounting plate. Disconnect the two blower wires.

•

Replace the blower and reconnect the two wires.

When replacing the rear panel, ensure that the wires are neither pinched nor interfere with the blower

operation. Re-secure the air intake manifolds.

INSTALLATION THROUGH THE FIREBOX:

REPLACEMENT BLOWER ACCESS GASKET IS REQUIRED.

•

Turn off the electrical power and the gas supply to the appliance.

•

Open the lower control door, the two side doors, and the fi re viewing door. Remove the logs.

•

Remove the blower access plate held on with 8 screws.

•

Disconnect the two blower wires. Remove the blower

bracket held on with 2 screws.

•

Replace the blower using the existing bracket. Replace

the bracket/blower assembly on the appliance.

•

Reconnect the two wires. Hold the replacement gasket in

place and reattach the blower access plate. Replace the

logs. Close all doors.

Turn the gas supply and electricity back on.

Because the blower is thermally activated, when turned on, it will

automatically start approximately 15-30 minutes after lighting the

appliance and will run for approximately 30-45 minutes after the appliance has been turned off. Use of the fan

increases the output of heat.

Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented from

coming into contact with the blower or its compartment.

Any damage resulting from this condition is not covered by the warranty policy.

black

white

red

BLOWER

THERMAL
SWITCH

VARIABLE
SPEED
SWITCH

BLOWER

SCREWS

AIR INTAKE MANIFOLDS

SCREWS

BLOWER ACCESS

PLATE

Содержание Haliburton GDS28-1NE























































Результаты поиска

Содержание Haliburton GDS28-1NE

Отзывы:

Похожие инструкции для Haliburton GDS28-1NE

Бренды по названию

Популярные бренды

Napoleon Haliburton GDS28-1NE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Haliburton GDS28-1NE

Отзывы:

Похожие инструкции для Haliburton GDS28-1NE

Бренды по названию

Популярные бренды