manualshive.com logo in svg

Napoleon GVF40P, Инструкция по установке и эксплуатации

Поделиться
Скачать
Napoleon GVF40P Скачать руководство пользователя страница 10

10

W415-0810 / 06.11.09

2.4 ELECTRICAL 

CONNECTION

!

WARNING

DO NOT USE THIS HEATER IF ANY PART HAS BEEN UNDER WATER. CALL A QUALIFIED SERVICE 

TECHNICIAN IMMEDIATELY TO HAVE THE APPLIANCE INSPECTED FOR DAMAGE TO THE 

ELECTRICAL CIRCUIT.

RISK OF ELECTRICAL SHOCK OR EXPLOSION. DO NOT WIRE 110V TO THE VALVE OR TO THE 

APPLIANCE WALL SWITCH. INCORRECT WIRING WILL DAMAGE CONTROLS.

ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE 

WITH LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 
CANADIAN ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE 

ANSI/NFPA NO. 70 IN THE UNITED STATES.

For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient  
location. Route a 2 strand, solid core millivolt wire from the valve to the wall switch or millivolt thermostat. The 
recommended maximum lead length depends on wire size:
 

WIRE SIZE 

 

MAX. LENGTH

 14 

gauge 

 100 

feet

 

16 gauge 

 

  60 feet

 

18 gauge 

 

  40 feet

Disconnect the existing wires from terminals 1 and 3 (from the
ON/OFF switch) and replace with the leads from the wall switch / millivolt thermostat.

50.1

P

I

P ILOT

3

1

2

N

O

L

O

T

H I

L O

FF

O

2.5 RATING 

PLATE

WARNING: FIREPLACE SCREENS MUST BE CLOSED WHILE IN OPERATION.

 DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN

CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE. DO NOT USE BLOWER INSERT, HEAT EXCHANGER INSERT OR OTHER
ACCESSORIES NOT APPROVED FOR USE WITH THIS HEATER. IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTAINANCE CAN CAUSE PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF LIFE. REFER TO THE OWNER'S INFORMATION MANUAL PROVIDED WITH THIS APPLIANCE. INSTALLATION AND SERVICE MUST BE PERFORMED BY A
QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER.

W385-0254

MADE IN CANADA

WOLF STEEL LTD, BARRIE, ON, CANADA

SERIAL NUMBER: 

    

GVF40 / CVF400

*

 

MAXIMUM HORIZONTAL EXTENSION:  2". SEE INSTRUCTION

MANUAL FOR GREATER EXTENSIONS.

ELECTRICAL RATING: 115V 0.82AMP, 60HZ
OPTIONAL FAN KIT: GZ550-KT

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS:

TOP / SIDES / BACK / FLOOR

0

RECESSED DEPTH

25¼"

MANTLE

5"

 

*

CERTIFIED UNDER: ANSI Z21.11.2-2000 VOLUME II, UNVENTED ROOM HEATER

CERTIFIED FOR USA

 ALTITUDE

INPUT

REDUCED INPUT

ORIFICE

MANIFOLD PRESSURE: 

10" WATER COLUMN

MINIMUM SUPPLY PRESSURE: 

11" WATER COLUMN

MAXIMUM SUPPLY PRESSURE:

 13" WATER COLUMN

SIT CONTROL:

 #820636

OPERATING PILOT OXYPROTECTOR:

 #8404

MANIFOLD PRESSURE: 

3.5" WATER COLUMN

MINIMUM SUPPLY PRESSURE: 

4.5" WATER COLUMN

MAXIMUM SUPPLY PRESSURE:

 7.0" WATER COLUMN

SIT CONTROL:

 #820637

OPERATING PILOT OXYPROTECTOR:

 # 8214

**

ABOVE 2,000FT, CONSULT LOCAL AUTHORITY HAVING JURISDICTION

 NOT FOR USE WITH SOLID FUEL.

 

**

0-2000FT (0-610m)

30,000 BTU/h

20,000BTU/h

#39

0-2000FT (0-610m) 

**

28,500 BTU/h
22,000BTU/h
#53

GVF40-N / CVF400-N

MODEL

GVF40-P / CVF400-P

MODEL

THIS APPLIANCE  MAY  BE  INSTALLED  IN AN AFTERMARKET,
PERMANENTLY LOCATED, MANUFACTURED (MOBILE) HOME, WHERE
NOT PROHIBITED BY LOCAL CODES. THIS APPLIANCE IS ONLY FOR USE
WITH THE TYPE OF GAS INDICATED ON THE RATING PLATE. THIS
APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES.

THIS IS A GAS-FIRED UNVENTED ROOM HEATER THAT REQUIRES AD-
EQUATE COMBUSTION AND VENTILATION AIR. THIS UNIT IS 

NOT 

APPROVED

FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION.

REFERENCE # W/N 15515

For rating plate location, see “DIMENSIONS” section.

Содержание GVF40P





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды