Push Button Layout:
PROGRAMMING INSTRUCTIONS:
Note
: The flashing cursor denotes location of data entry se-
lection to be made. If an entry was made in error or requires
changing, depress
SET
to backspace, make the correct se-
lection and depress
ENTER
to accept data and advance the
cursor.
A. SETTING CLOCK/CALENDAR:
Upon initial power up will appear in display.
Depress
SET
. will appear in display.
Depress
ENTER.
will appear in display.
Enter the current date, day of week and time (military) by de-
pressing
UP
and
DWN
to make the selection then depress
ENTER
to accept.
To program Daylight Saving Time (refer to
D. Setting Block
Events (Weekly Repeat)
and
F. Daylight Saving Time
).
To change or program clock/calendar simply repeat the steps
above.
B. SETTING EVENTS:
Depress
SET
until "
ENTER TO SET EVENT"
appears in display.
Depress
ENTER. w
ill appear in display.
Note:
A01 indicates Channel A event 01.
When cursor appears you are able to scroll through events.
Depress
ENTER
until the flashing cursor appears under OFF
in display. Now select type of event required by scrolling us-
ing the
UP
and
DWN
push buttons until either:
ON - Relay ON (latching mode).
OFF - Relay OFF (latching mode).
PL - Relay Pulse (momentary).
...appears in display and depressing
ENTER
will make the
selection.
When selecting the pulse mode, PL01 will appear in the dis-
play. It is now necessary to assign the length of time (duration
of relay activation). The pulse can range in length from 1-
second minimum to 15-seconds maximum and is selected by
using
UP
or
DWN
push buttons, and then depressing
ENTER
to accept.
Note:
If pulse duration is not selected, relay output defaults to
1-second. Next, select the day of the week or BK* for weekly
repeat and time (military) by scrolling using
UP
and
DWN
push buttons and depressing
ENTER
to accept. You may
continue to program events by repeating the previous steps or
exit programming by depressing
SET
.
Note:
When programming additional events, it is necessary
to select the next consecutive event number following the last
event program to continue.
Note:
When it is required to have the same event repeated
on two (2) programmed as a block by selecting
BK
in the day
field.
Note:
To program the consecutive days of the week, refer to
D. Setting Block Event (Weekly Repeat)
and
F. Daylight
Saving Time
.
C. ADDING EVENTS
Depress
SET
until
"ENTER TO SET EVENT"
appears in display.
Depress
ENTER.
will appear in display.
Depress
ENTER.
If the event is not programmed, the cursor
will move to the OFF (relay function) position. If the event is
programmed, the cursor will move to the position and the pro-
grammed information of the event will be displayed. At this
point, depress the UP button to step up through the pro-
grammed events. When an unprogrammed event is reached,
the cursor will move to the OFF (relay function position). (At
this point, see
Setting Events
or
Setting Holiday Events
).
D. SETTING BLOCK (WEEKLY REPEAT)
Select channel A or B by moving slide switch SW1 to ap-
propriate position.
Note:
Channel cannot be changed in the middle of program-
ming events. To change channels, you must exit program-
ming, then change channel switch position, then enter pro-
gram mode again.
Depress
SET
until appears in display.
Push Button Description Table
Push
Button
Function/Description
SET
Scrolling keys for programming. Escaping out of
existing programming.
ENTER Accepts selections made to programming.
UP
Scrolls through selections.
DWN
Scrolls through selections.
UP
and
DOWN
keys can be used to select data entries.
After scrolling to the correct entry, depress
ENTER
to ac-
cept.
SW1 clip SW Selects channel to be programmed.
SW2 slide SW Selects tandem or individual relay operation.
(CUT R3)
CH ON
SU 01:01
ENTER TO
SET TIME
01/01/01
SU / 01:01
A01 OFF
SU 00:00
A01 OFF
BK 00:00
A01 OFF
SU 00:00
ENTER TO
SET BK
Lithium Battery Socket
(order Model CR2032)
12-24 Volt
AC/DC input