NAPCO Gemini GEM-P3200, Инструкция по программированию, Страница: 55 / 68

L
NAPCO Security Systems
X
GEM-P3200 Programming Instructions
Page 55
WI818G 10/05
KEYPAD CONFIGURATION MODE
This section will focus on configuring the GEM-RP1CAe2/GEM-K1CA Keypads. If there is more than one keypad in the system, only
Keypad No. 1 may be used for programming.
KEYPAD INSTALLATION
Two types of keypads may be used with the GEM-P3200: the GEM-RP1CAe2/GEM-K1CA. Each must be assigned an address
number (1–7) and each requires its own configuration procedure (see CONFIGURING THE KEYPADS, which follows, and DIRECT
ADDRESS KEYPAD AREA OPTIONS).
At least 1 keypad must be used; only 1 is required for a single-area Commercial Burglary
installation.
GEM-RP1CAe2/GEM-K1CA
- is a 2-line combination fire/burglary/access keypad capable of supporting 4 EZM zones and a
PGM output. The GEM-RP1CAe2 or GEM-K1CA is recommended for use as Keypad #1. See "Important Note" on page 2
for more information regarding the various buttons on the GEM-RP1CAe2/GEM-K1CA keypads.
CONFIGURING THE KEYPADS
A total of up to 7 keypads may be connected to the panel.
Configuring the GEM-RP1CAe2/GEM-K1CA Keypad
Each GEM-RP1CAe2/GEM-K1CA keypad must be configured for (a) keypad tactile beep; (b) entry sounder; (c) keypad address; (d)
compatibility number; (e) EZM address; and (f) zone response.
To enter the Keypad Configuration Mode:
1. Move jumper JP1 (located in the center of the control panel board) from Pins 1-2 (top two) to Pins 2-3 (bottom
two). NOTE: See Wiring Diagram on page 68.
2. After about 15 seconds, the display will read “
XX OUT OF SYSTEM
”, where XX indicates the keypad address.
3. Press 11123 R and proceed as follows. (Repeat the following procedure for
all keypads).
Keypad Tactile Beep
Upon entering the Keypad Configuration Mode, “
KEYPAD BEEP ON
” will be displayed,
indicating that the tactile beep, which sounds when any button is pressed, is on.
To turn off the tactile beep, press the
U
button (the
U
button will toggle the tac-
tile beep on and off). Press
R
to continue or press
C
to exit.
Entry Sounder
To turn off the keypad entry sounder during entry time, press
U
(the
U
button
will toggle the entry sounder on and off). Press R to continue or press
C to exit.
Keypad Address
If more than one keypad is installed, each must be assigned a unique keypad
address (that is, no two keypads may be numbered alike):
Keypads must be numbered consecutively (missing numbers are not permitted)
Only Keypad No. 1 may be used for programming.
To assign the keypad number, proceed as follows:
1. Enter the assigned keypad number 01–07, then press
U
to save. A valid
number will be acknowledged by a short beep; an invalid number will be re-
jected by a long beep.
2. Press
R
to continue or press
C
to exit.
Keypad Beep
ON
NORMAL
KEYPAD
CONFIGURE
R
COMPUTERIZED SECURITY SYSTEM
GEMINI
ARM
ED S
TAT
US
SYSTEM ARMED
01/01/97 12:00AM
1 2
4 3
5 6
7 8 9 0
A
B
C
D
E
F
G
NEXT/YES
PRIOR/NO
AREA
# OF ZONES IN AREA 1
ENTER # ZONES X X # OF ZONES IN AREA
ENTER # ZONES XX
Entry Sounder
ON
Keypad Address
01