NAPCO Certa-Set Скачать руководство пользователя страница 4

Страница: 4 / 18

napcopipe.com

2. After inserting the O-ring, screw the assembled riser onto the sled coupling by hand (clockwise). Hand tighten

until it is seated. No tools are required. Do not overtighten.

3. Once riser and sled coupling are assembled, attach the sprinkler to the sprinkler end of the riser.

B. ½" Aluminum Assembled Riser (manufactured by others)
1. The ½ riser consists of the following pieces: A ½" riser cap, chevron gasket and ½" assembled riser.

Note: NAPCO does not manufacture or warranty ½" risers beyond the riser cap.

Position riser to align with

sled coupling

Hand tighten

No tools required

Hand tighten

Place [MRDC] [MR] or [MDC]

onto riser first

Hand tighten

Place sprinkler head onto

[MRDC] [MR] or [MDC];

hand tighten

Place [MRDC] [MR] or

[MDC] onto riser first

Sprinkler head installed

Do not install sprinkler head

with [MRDC] [MR] or [MDC]

Components to field

assemble ½" riser

Содержание Certa-Set


















Результаты поиска

Содержание Certa-Set

Отзывы:

Похожие инструкции для Certa-Set

Бренды по названию

Популярные бренды

NAPCO Certa-Set, Руководство по монтажу на объекте

Результаты поиска

Содержание Certa-Set

Отзывы:

Похожие инструкции для Certa-Set

Бренды по названию

Популярные бренды