nanoplanes Baby Shark Скачать руководство пользователя страница 13

Страница: 13 / 14

A view of the tight

installation shown

The battery connector

showing through the

hole.

You need to fill this

hole and space under

the front bottom. Cut

scrap piece 3/4” Keep

the battery away from

those sharp screws and

prevent the battery from

sliding too far forward.

Cut more scrap pieces

from the “T” jig.

Fill up the front cavity

ONLY 3/4” deep so that

the battery position will

slide partially into the

nose area and not hit

the screws.

Test fit your battery and

check for proper CG.

Once proper CG is

determined fill up the

front cavity to allow

your battery to be

placed on the proper

CG every time. Glue

the scraps in place.

As you did with the

rear hatch, simply tape

down the top cover.

You may want to lightly

sand the edges smooth

before attaching it.

Unless you don’t mind

the way it looks.

The tape over the rear

hatch as shown. Again

lightly sand the edges

rounded while holding

it down before taping

the edges if you want

streamlined rounded

edges

For you to better

understand where to

tape I have used the

blue tape for

demonstration purpose

only. You should use

clear tape on yours.

Sand all edges of your

fuselage as streamlined

as you wish it to be. (Be

careful not to damage

the rudder or horizontal

stabilizer when sanding

the rear section.

Congratulations! You are almost done!

As a last step you should cover the entire fuselage

with clear packing tape to add strength and apply a

coating of water based polyurethane over the entire

plane. The WBPU will help keep the airplane clean.

To see how to cover your plane with tape refer to

the last couple pages of the NANOSHARK manual.

IT IS VERY IMPORTANT TO PROPERLY SET UP
YOUR CONTROL SETTINGS AND THROWS.
PLEASE READ ALL THE INFORMATION ON THE
PAGE BELOW.

Warning! This aircraft is for experienced pilots only.
This is not a PARKFLYER. Although it weighs under
2LBS, its speed can exceed 60mph. Therefore, it does

not qualify as a “Parkflyer” as per AMA rules and reg

ulations. It should be flown only in fields specifically

reserved for RC aircraft which have been approved by
the AMA. It is highly recommended that you join the

AMA if you are not already a member. If built or flown

incorrectly, this plane can cause damage property or
injury to people. User assumes all responsibilty and
risk.

Содержание Baby Shark















Результаты поиска

Содержание Baby Shark

Отзывы:

Бренды по названию

Популярные бренды

nanoplanes Baby Shark, Руководство пользователя

Результаты поиска

Содержание Baby Shark

Отзывы:

Бренды по названию

Популярные бренды