manualshive.com logo in svg

Nanomotion AB5, Руководство пользователя

Поделиться
Скачать
Nanomotion AB5 Скачать руководство пользователя страница 16

 

Connections and I/O Settings 

10

 

2.5.1  Voltage Source Configuration 

The opto-isolated input signals (2.2.1) are activated as short-to-ground. The voltage 
for the opto-isolated circuit (see Figure 6) is provided by either the in3.3V 
supply (default state) or an external voltage supply via pin 13 on the I/O Port 
connector. The input to be activated should be shorted to external voltage supply 
ground. 
Configure jumper JP2 on the top AB5 card according to the voltage source:  

Pin 1 shorted to Pin 2, for an in3.3V source (default factory setting) 
Pin 3 shorted to Pin 4, for an ex3.3V voltage source 

Connection for

Internal

 source

JP2

3

Connection for

External

 source

4

1

2

JP2

3

4

1

2

 

Figure 6: Jumper 2 Configuration 

 

ATTENTION: 

Do not short other pins on JP2. Doing so shorts the 
external power supply to the +3.3V supply! The input 
circuit is limited to sink up to 10 mA but not less than 3 
mA. 

Содержание AB5


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды