a
To install the light bars on the light track (8 light bars for an example)
1. Place 8 light bars on a sturdy and flat surface with the diode array facing down (Fig.a).
2. Adjust the light bar direction, rotating every other light bar 180 degrees to ensure all
neighboring light bars are plugged in on opposite sides. (Fig.d)
3. Attach light track above the light bars. Make sure light bars are properly centered on
each corresponding mark. (Fig.b&c)
4. Insert the Fast Mounting Clip into the groove on light bar (Fig.e). Slide clip into light
track until the clip is in place to hold the light bar (Fig.f). Press the fast mounting lever
to lock in place (Fig.g).
5. On the light track, you will find a dust cap covering the input port. Remove dust cap,
then insert and tighten light bar cable firmly into jack (Fig.h).
6. Insert the M6 screw and nut into the support frame at first, but do not tighten your
screws (Fig.i); Leave space between the nut and support frame. Slide them into the
light track (Fig.j); Adjust the support frame to keep the balance, and then tighten the
M6 screws.
Fixture Hanging (Wires/Ratchets)
1. Attach the carabiners from the steel wire hanger (optional) to the hanging hole (on the
support frame).
2. Hang the fixture in the desired location.
Single Light Bar Installation:
Method#1: (Tab with eye-lit)
Slide the tab into light bar adjusting it in a desired place (keep the balance), and then
insert and tighten M6 screw nut to secure it (Fig.k).
Attach the carabiner from the steel wire hanger to the light bar hole (A). Hang the fixture
in your hanging support frame (B).
Method#2: (Hook)
Slide the hook into the light bar adjusting it in a desired place (keep the balance) (Fig.m).
Hang the fixture in your hanging support frame (Fig.n).
TECHNICAL SPECIFICATIONS
ASSEMBLY INSTRUCTIONS
ABOUT PRODUCT
LEDex F110
AC120V/208V/240V/277V
110W each
@277V 2.70-2.75µmol/J
Full Spectrum
45.8x2.0x1.7inch / 4.0lbs
1163x50x43mm / 1.8kgs
≧
50,000hrs
0-10V SLC &
DTU NCCS-APP-2.0
120°
Lifetime
Model
Light Distribution
Dimming
Input Voltage
Light Bar
Input Power
Efficacy
Spectrum
Light Bar
Dimensions/ Weight
You can use up to16 light bars depending on track length letting you meet your
overall desired PPFD to your canopy. It is recommended to keep a mounting height
of 6”-12” (15.2cm-30.4cm) above canopy for optimal light efficiency and uniformity.
Growers should regularly monitor the temperature at the canopy level to ensure the
appropriate height of the fixture is correct, as canopy temperature and ambient room
temperature can differ.
Support Frame
Fast Mounting Clip
Light Track
Light Bar
Cable
Input Port
0-10V Jack
Light Bar
e
f
g
A
B
PLEASE READ THESE INSTRUCTIONS
FIRST BEFORE INSTALLATION
Congratulations on the purchase of your new Nanolux LED. We have done everything to
ensure a long product life and safe operation, but the installation and use of the product
is at the responsibility of the user. Incorrect use or installation can lead to failure and
damage to the luminaire. Damage to the luminaire or electronic circuitry as a result of
incorrect installation or use will revoke your warranty. Read this manual carefully before
installing your luminaire.
k
h
j
j
i
Single Light Bar Use:
If single bar is purchased for side or inter-canopy lighting, a separate power cord for each
light bar is needed.
m
n
8
7
6
6
7
8
b
c
d
CAUTION :
* Don’t remove the protective paper preventing damages to the diode array when
handing light bars.
* Use the figure tag on the top of each light track as a convenient installation template
for light bar. For instance, 8 light bars correspond to “8”(the figure tag), if 8 light bars
are selected to use.
* Be sure light bar and track are clean, and wear cotton gloves.
* When you insert the light bar cable, please do not go across the light track.
-02-
-03-
LEDex R110
LEDex R/B110
LEDex UV55
AC120V/208V/240V/277V
110W each
@277V
2.45-2.50µmol/J
@277V
2.60-2.65µmol/J
@277V
2.70-2.75µmol/J
Ultraviolet
55W each
@277V 500mW/J
Red
Blue
Red and Blue
45.8x2.0x1.7inch / 4.0lbs
1163x50x43mm / 1.8kgs
≧
50,000hrs
25%-40%-55%-70%-85%-100%
0-10V SLC & DTU NCCS-APP-2.0
40%-55%-70%-80%-90%-100%
0-10V SLC & DTU NCCS-APP-2.0
120°
Lifetime
Model
Light Distribution
Dimming
Input Voltage
Light Bar
Input Power
Efficacy
Spectrum
Light Bar
Dimensions/ Weight
*Subject to change without notice, Tolerance ±10%
LEDex B110
