11111111 )� PLEASE READ THESE INSTRUCTIONS
11111111 '/
FIRST BEFORE INSTALLATION
Congratulations on the purchase of your new Nanolux CMH-315NC fixture
We have done everything to insure a long life and safe operations, but the
installations and use of the ballast is the responsibility of the user. Incorrect
use or installations can lead to failure and damage to the ballast. Damage
to the luminaire and electronic circuitry as a result of incorrect
installations and use revokes your warranty. Read this manual carefully
before installing your luminaire.
CD
TECHNICAL SPECIFICATIONS
Model
Input Voltage
Output Voltage
Input Frequency
Output Power
Power Factor
Crest Factor
THD
Dimming
Strike lamp
Protection
Function
Size
(l*W*H)
Weight
CMH 315NC
No Fan
120VAC,240VAC,27NAC(Optional)
80VAC-1S0VAC
50Hz-60Hz
315W Max
�0.99
,;1.7
;;10%
none
CMH 315W
Over Temperature;Over/Under Voltage;Open/Short Circuit
554*420*243mm(21.8*16.5*9.6 inch)
6.0kgs(13.21bs)
� INSTALL FIXTURE ON BALLAST
0
1. Make sure power is off!!!
2. Insert the fast mounting clips into the cutout in the center of the ballast,
and slide them off to opposite sides.
3. Hold the fixture from its base and plug in the fixture bu inserting terminal
into the socket.
4. Slide the fast mounting clips into the grooves on the ballast until they are
in place to hold the fixture.
5. Press the fast mounting lever to lock in place.
6. Confirm the fixture is installed on the ballast properly and is not loose.
0
1) Place the reflector over the three bolts on the mounting frame of
the ballast. Align the hood so that the pin alignment hole on the
hood is in the same quadrant as the alignment hole on the ballast
frame.
2) Rotate the hood clockwise so the hood is aligned squarely with
the ballast assembly.
-01-
0
Adjust the reflector to
secure the pin into
the hole.
·�o�•
[�
SCOPE OF USE
The Nanolux CMH-315NC fixtures are designed to drive horticultural
ceramic metal-halide lamps for plant cultivation. They are intended for
climate room use. They are suited for damp locations but should not
be used outdoors or in wet environments.
High Intensity Discharge lamps generate intense heat. Installations of HID
lamps should follow local installation and safety regulations.
1••�f
INSTALLATION COMPLY WITH LOCAL
..-. INSTALLATION REGULATIONS
These luminaires are suitable for a damp indoor location. Do not install
your luminaires in a wet environment or outdoors.
Do not operate these luminaires close to combustible materials. The lamp
and reflector will get hot during operation. Do not touch the reflector or
lamp during or right after operation. Make sure the power cord does not
touch any hot part of the luminaire. Make sure the lamp is clean and
inserted correctly.
A normal operating environment temperature should be below 122
°
F.
Exceeding the maximum environmental temperature will stress electronic
components, which will lead to shorter lifetime and decreased reliability.
When using a NCCS RTU in the USB port of a Nanolux ballast, the Dimming
function control dial on the ballast will be taken out of function.
-02-
RTU is removed from the ballast during operation OR the RTU loses comm
unication with the DTU for any reason, the ballast will automatically turn off
after 10 minutes. The ballast has to be unplugged from the power source and
turned back on to reset. The ballast will then run in regular mode (no NCCS)
or if a RTU is plugged in, it will operate in NCCS mode. If the ballast continues
to turn off for any reason during operation with the RTU in NCCS mode, replace
the RTU and confirm it is communicating with the DTU.
For further NCCS APP customer support and tech support pages, visit
www.nanoluxtech.com.
LAMP REPLACEMENT AND HOT
RESTRIKE
CA UTION:
00 0
& &&
• Always install the lamp before connecting your luminaire to mains.
• Allow lamp to cool 30 minutes before restarting (hot restrike).
• When changing the lamp always disconnect the luminaire from mains
by removing the mains plug. Let the lamp and reflector cool down for
30 minutes before changing as they are very hot. When replacing a
defective lamp without disconnecting the mains, the lamp will not
start. Disconnecting the power and reconnecting it will restart theballast.
TO TAKE OUT A LAMP:
• DISCONNECT THE MAINS FIRST
• The base has two prongs that are twisted counter-clockwise then
pulled outward. It is recommended to handle and hold the lamp by its
base in order to prevent breaking the lamp.
TO INSTALL A NEW LAMP:
• DISCONNECT FROM MAINS FIRST
• Make sure the lamp is clean, wear cotton gloves and clean the lamp
after installation with a dry soft cloth. Never use detergents to clean
a lamp, use pure alcohol or wipe clean with a dry clean soft cloth.
• Hold the lamp from its base and align the terminals to the sockets
• Hold the lamp from its base and Plug in the the lamp by inserting
both terminla in the socket and press together firmly.
• Turn the lamp in a clockwise to lock in place (or lock)
• Wipe the lamp with a clean soft cloth.
• Be sure not to touch the reflective material of the reflector with your
bare hands.
-03-
