background image

Antenna connector - GSM/GPRS
For connecting antennas for GSM/GPRS there is a conne-
ctor of type SMA on the circuit board of the REGGAE GT 
communicator  Any antenna that satisfies the necessary 
operation conditions  in the range GSM/GPRS 900/1800 
MHz with impedance 50 Ω can be used 

Antennas must be adapted for both indoor and outdoor 
usage 

Antennas with a magnetic base are most commonly 
used, and these can be fixed to the outer surface of the 
panel or REGGAE communicator cases 

Telephone unit of communicator
The telephone unit of the circuit board of the REGGAE 
GT communicator is able to communicate with the AS  
panel in all common pulsation and DTMF formats  Supp-
orted formats are 4+2, Ademco Point ID (Contact ID), 
communication speed 10, 20 or 40 bps with handshake 
1400 Hz, 2300 Hz or multi-tone 

Dialled telephone numbers can be set up as pulsation or 
DTMF at the AS panel 

The telephone unit of the REGGAE GT communicator can 
generate the dialling tone of the line for the AS panel 
(from the FW 6 xx communicators)  This function is optio-
nal in the communicator configuration 

The terminal plates marked „T1“ and „T2“ are used for  
connecting telephone lines from the AS panel  If the AS 
panel has to communicate directly with the ARC, the 
PSTN telephone line must be connected to the terminal 
plates marked  „TIP“ and „RING“  Also, if the communicator 
has to send news and occurences on the ARC channel, 
the VTS telephone line must be connected to the termi-
nal plates marked „TIP“ and „RING“ 

Tampers on the communicator
The connectors TMP1 TMP2 on the circuit board of the 
REGGAE GT communicator are used to connect up to 
two tampers  The connector has four pins  The two pins 
on the left side marked TMP1 are used to connect the first 
tamper  The two pins on the right side marked TMP2 are 
used to connect the second tamper 

For both tampers it is assumed that contact will be  
released immediately if they are disrupted 

The tamper on the box of REGGAE GTbz/GTbzxxx com-
municators is standardly connected as TMP1  TMP2 is 
normally used for power outage detection 

U

S

E

R

 

M

A

N

U

A

L

REGGAE GT/GTbz 

Communicator for GSM (GPRS/SMS) transmission

www.namsystem.com

10

Содержание REGGAE GT


















Отзывы: