Nakayama PB4320, Руководство пользователя

Страница: 16 / 84

Model: PB5221 PB5600/PB5450 PB7500 PB7700
Displacement: 52cc 52cc 63.3cc 63.3cc
Horsepower:
2hp 2.3hp / 2hp
3hp 3hp
Anti-vibration
System:
N/A YES /
N/A
YES
Shaft
dimensions:
28mm*1.5m 28mm*1.5m 28mm*1.5m
28mm*1.5m
Net weight: 7.6kg 8.5kg 8.8kg 10.8kg
* The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the prod -
ucts. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in
the product you just acquired.
Assembly and main adjustments
Installing the handle (Picture C
,
page 2)
• Loosen the 4 bolts on the upper cap and insert the handle.
Re-tighten the bolts securely.
Installing the handle (Picture C
,
page 3)
• Install handle in bracket. Position handle in a comfortable operating position and tighten the M5X30 and M6X50 screws.
Warning! Do not a tt empt to disassemble the two special screws. The two clamps position has been adju s ted at a suitable place,do not a tt empt to
remove or move them. Otherwise,it can result in serious personal injury.
Installing the handle (Picture C1, page 2)
• Install handle in bracket. Position handle in a comfortable operating position and tighten U Handle Screw Assy.
Technical Data
1. CUTTING HEAD: Equipped with a cutting Disk or a replaceable nylon trimming line that advances when the trimmer head is tapped against the ground
while the head is turning at normal operating speed.
2. DRIVE SHAFT ASSEMBLY: Contains a specially designed inner flexible drive shaft.
3. THROTTLE TRIGGER: Spring loaded to return to idle when released. When accelerating, press trigger gradually for best operating technique .Do not hold
trigger while starting.
4. IGNITION SWITCH: Move switch forward to stop, back to start.
5. THROTTLE LOCKOUT: Before acceleration, compress it please.
6. U-HANDLE: this handle can be adjusted at you convenience for comfort.
7. HARNESS ASSEMBLY: a attachment which hang the machine on the operator and adjustable in length.
8. AIR CLEANER COVER: Contains replaceable felt element.
9. FUEL TANK LID.
10. FUEL TANK: Contains fuel and fuel filter.
11. Priming Bulb: Pressing the priming bulb pumps( 7 to 10 times before starting),will remove all air and stale fuel from fuel system and bring fresh fuel to the
carburettor.
12. CHOKE: the choke control is located on the top of the filter cover.
COLD STARTS: Pull lever up to close choke for cold starts. Push lever down for RUN position.
13.DEBRIS SHIELD: Mounted just above the cutting attachment. Helps protect operator by deflecting debris produced during the trimming operation. Do not
operate unit without shield.
14. CUT-OFF KNIFE: Trims nylon filament to the correct length-7” ,head to end of line-when nylon trimming head is bumped on the ground during the oper -
ation of advancing the line .If trimmer is operated without a cut-off knife the line becomes too long(more than 7”) the operating speed will slow down the
engine, this will overheat or damage the engine.
15. BLADE: Circular blade for grass, weed or brush cutting applications. Harness, plastic shield and U-Handles required for blade operation.
16. THROTTLE LOCK (not included on all models)
N/A
Type: NAKAYAMA NAKAYAMA PRO NAKAYAMA PRO NAKAYAMA PRO
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer
shall not be liable for injuries and damages resulting from the use of non-conforming equipment.
EN
Identify the parts illustrated on pages 2-3 and follow the corresponding instructions depending on the type of your brush cutter.
Description of main parts (Pictu r e A, page 2 or 3)
WWW.NIKOLAOUTOOLS.GR
16
PB 4320 *
43 cc
1.8 hp
N/A
26mm
7. 4 kg
NAKAYAMA
* PB4320: Two - stroke air-cooled engine , Loop handle , Double belt , Automatic head , 255mm (3T) blade