manualshive.com logo in svg

Nakanishi Sonic Cutter ZERO, Руководство по эксплуатации, Страница: 17 / 23

Поделиться
Скачать
Nakanishi Sonic Cutter ZERO Скачать руководство пользователя страница 17

36

7 

Trouble-shooting

7 – 1 

Error code

If a problem occurs with the product, an error code will be displayed on the display unit on the 
operation panel.

1 

Stop the operation at once.

2 

Press the ON / OFF key, or step on the footswitch again or turn it back on and see if the 
error is resolved.

3 

If the error appears again, please refer to the following table for solutions.

Error code

Error Description

How to remedy the Error

System error

Please return complete unit for service.

Handpiece overload error
( Excessive load or force on the blade. )

Reduce the cutting pressure or working force 
applied to the blade.

Amplifier error 
( Board heat generation error )

Allow the unit to cool and turn it back on. Do not put 
excess load on the blade. Also, make sure that the 
blade is not loose. If it is loose, tighten it securely.

Excessive input voltage

Please return complete unit for service.

Under Input Voltage

Please return complete unit for service.

Amplitude feedback residual voltage 
error

Please return complete unit for service.

Handpiece fever abnormality

Check for loose blade. Tighten blade firmly.

Start frequency confirmation error

Please return complete unit for service.

Resonance frequency search timeout

 (This is an error if the resonant frequency 
of the integral tool, tip holder, or tip that is 
installed is not found.)

Check for loose blade. Tighten blade firmly.

Frequency pull-back anomaly

(This is an error when the resonance 
frequency changes significantly during 
operation.)

Check for loose blade. Tighten blade firmly.

Memory failure

Please return complete unit for service.

Forced deactivation when not in use

The factory default setting is "3 minutes". (See "6-2 
Setting the Forced Stop Time When Not in Use".)

Excessive amplitude of the oscillator 
feedback signal

Please return complete unit for service.

Содержание Sonic Cutter ZERO
























Отзывы:

Нет отзывов