manualshive.com logo in svg

Naigon Electronic Spark Color SC2-R3, Руководство по установке

Поделиться
Скачать
Naigon Electronic Spark Color SC2-R3 Скачать руководство пользователя страница 30

Page | 30 

 

Entry 

Label 

Action 

Description 

Aux Button 

AUX +/- 

Press 

Pressing the aux button engages Blaster Block mode. Once in 
this mode, swinging the saber will perform EzBlaster™, where 
another Blaster Block will be performed. Keeping the saber 
still will cause the mode to exit. 

Aux Button 

AUX +/- 

Hold 

Holding the aux button is the second way to engage the 
Lockup effect; the primary way is by EzLockup™ - tapping the 
aux once after performing a Clash. Depending on the chosen 
config setting, either releasing the button or tapping it again 
will cause the mode to exit. 

Aux Button 

AUX +/- 

Press (in 
Clash) 

Pressing the AUX button will perform EzClash™; immediately 
after the press the Lockup sound will play when in Clash 
mode. This is the preferred way to perform a clash on 
Igniter™. 

Swing saber 

NA 

Swing 

Swinging the saber causes a single swing sound to be played. 
If the swing is performed rapidly then a Slash sound will be 
performed. 

Rotate saber 

NA 

Rotate 

Rotating the saber will advance the color set to the next 
color, loading in the new blade, clash and blast colors. 

Hit saber/Blade  CS 

Clash 

Hitting the saber against something or hitting your hand on 
the hilt will cause the Clash sound to play. To return to 
running simply wait for the clash to finish. 

Main Button 

MAIN+/- 

Hold/Unlatch  Holding or unlatching the main button will cause the 

retraction sound to play and then the saber will return to Idle 
mode. 

6.3.

 

SABER TRACKS™ 

Saber Tracks™ is the special seventh (7

th

) font of Spark Color 2™ that can play the track files. Place 

track01.wav

, 

track02.wav

, …, 

trackNN.wav

, in the 

/TRACKS FOLDER

, and then engaging this font will immediately load into the 

effect and start playing the tracks. 

6.3.1.

 

SABER TRACKS INTERACTIVITY 

The following table describes the interactivity for Saber Tracks. 

Entry 

Label 

Action 

Description 

Aux Button 

AUX +/- 

Press 

Advances to the next track. When the last track file is reached 
it goes back to the beginning. 

Main Button 

MAIN +/- 

Hold/Latch 

Holding or latching the main button will enable the blade, 
doing the extension effect first then the pulse effect. 

Main Button 

MAIN +/- 

Hold/Unlatch  Holding or unlatching the main button will cause the blade to 

retract if the blade is current enabled. 

Aux Button 

AUX +/- 

Hold 

Holding the aux button will exit Saber Tracks™ and load the 
first font. 

 

6.4.

 

SABER CONFIGURATION 

Содержание Spark Color SC2-R3


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды