Naigon Electronic Spark Color SC2-R3 Скачать руководство пользователя страница 22

Страница: 22 / 33

Page | 22

individually; however, the easiest way is simply to pick the dropdown for the LED being used and it will be auto-
populated.

Figure 17 – Master settings in the config editor. Use the top dropdown to auto-set the 4 drive parameters below. Also set if the main switch

is momentary or latching, and if the boot sound is being used.

The rest of the settings are described as follows:

ORIENTATION

sets which way the board is facing in the hilt, so that the board can be aware of the saber’s angular

direction (ie which way it is pointing).

X-SABER

is the amazing new feature that allows an RGB color-mixing cross-guard saber! After enabling this make

sure to set each color set’s c4 values to non-zero in order for the side LEDs to turn on; see

4.6 X-SABER WIRING

for more details on wiring and settings

NEW IN R3

Only applicable for WS2812 strings.

REVERSE RED/GREEN (REVERSERG)

should be checked when

using the 5mm straw hat LEDs, to keep the colors consistent and to help prevent the annoying flash from happing
more than it needs to.

Require aux button when twisting requires the aux button to be held when doing the twist motion to advance to
the next color set. This prevents unwanted color shifts when swing the saber or dueling.

Содержание Spark Color SC2-R3


































Результаты поиска

Содержание Spark Color SC2-R3

Отзывы:

Бренды по названию

Популярные бренды

Naigon Electronic Spark Color SC2-R3, Руководство по установке

Результаты поиска

Содержание Spark Color SC2-R3

Отзывы:

Бренды по названию

Популярные бренды