background image

 

 

 

 

5

 

Installation and operation manual

DTH-V9-2020 

 

 

  
 

 

DTH  

Model 

Natural Gas

 

Dynamic supply 

pressure****

 

Nominal Manifold 

pressure* 

Pilot 

pressure 

Low fire inlet capacity 

Minimum 

In.w.c [kPa] 

Maximum 

In.w.c [kPa] 

At maximum capacity 

In.w.c [kPa] 

In.w.c [kPa] 

MBH 

Kw 

35 

7”

 

[1.74] 

10”

 

[2.5] 

2.3

” [0.

57] 

3.5

” [0.

87] 

30 

8.79 

40 

2.9

” [0.

72] 

50 

4.6

” [

1.15] 

55 

3.1

” [0.

77] 

40 

11.7 

65 

2.8

” [0.

69] 

75 

2.3

” [0.5

7] 

85 

2.9

” [0.

72] 

100 

3.8

” [0.

95] 

125 

2.6

” [0.

65] 

60 

17.6 

150** 

3.9” [0.97

150*** 

10”

[2.5] 

14”[3.5

]

 

4.0” [0.99

 

*: The pressure adjustment may vary slightly. See the unit name plate for the exact value.  
**

: With optional 2’’ NPT gas train.

 

***: With standard 1-1/2

’’ NPT gas train.

 

****: At maximum capacity (dynamic pressure). 

 
 
 

 
 
 
 
 

DTH 

Model 

Propane Gas

 

Dynamic supply 

pressure**** 

Nominal Manifold 

pressure* 

Pilot 

pressure 

Low fire inlet capacity 

Minimum 

In.w.c [kPa] 

Maximum 

In.w.c [kPa] 

At max. capacity 

In.w.c [kPa] 

In.w.c [kPa] 

Minimum 

In.w.c [kPa] 

Maximum 

In.w.c [kPa] 

35 

11

 

[2.74] 

14

 

[3.5] 

(Consult factory  

or rating plate) 

2.5

” [0.

62] 

30 

8.79 

40 
50 
55 

40 

11.7 

65 
75 
85 

100 
125 

60 

17.6 

150 

Gas pressure adjustments 

 

Содержание DTH Series












































Отзывы: