background image

CONTROLS AND CONNECTIONS

7

[Note: Always reset a channel’s

input Gain (or external devices’

output level) after altering the

amount of mixer equalization cut or

boost applied.]

The key to successful equalization

is to avoid excess. Too much

equalization on the input channels

will result in a mix that is smeared

together with nothing specifically

defined. During rehearsals,

experiment with the equalizer

controls on various instruments,

vocals and combinations of these

mixed together to become familiar

with various equalizer settings.

(6)  PAD

This switch attenuates the input

signal by -20dB. When connecting

a line level device to channels, or if

the mic input is distorted, set this

switch to the position of -20dB.

(7)  LINE INPUT

The Line input is designed to

accept balanced or unbalanced

line-level signals such as those from keyboards, drum machines,

or samplers. There is enough gain available on the line input to

accept even lower level signals, such as those from an

unbalanced microphone or guitar output. If a balanced signal is to

be connected to the line input, then a 1/4" TRS (stereo) phone

plug should be wired for:  Tip = positive (+), Ring = negative (-),

Sleeve = ground.

(Note: Only either the Mic or the Line input of a given channel

should be connected at one time.)

(8) MIC INPUT

The Mic input is an electronically balanced XLR type designed to

accept signals from any balanced or unbalanced low impedance

(Low Z) microphone. The XLR jack is configured for: Pin1 =

ground, Pin2 = positive (+), Pin3 = negative (-).

(12)

(13)

(12)

(10)

(11)

(10)

(11)

(9)

(9) L AND R CHANNEL GRAPHIC EQUALIZER

The 7-band channel graphic equalizer allows you to adjust the

frequency response of the L and R Channel bus signal, providing

a maximum of 

±

12dB of cut and boost for each frequency band

from the flat position. When in BRIDGE MODE, the L-Channel EQ

controls the output.

(10) L AND R AMP PROTECT LED

These LEDs will indicate the operation of the protection circuits in

the POWER AMP (L and R) section. Shut off unit if this lights

during use, and check output connections. Do not operate the unit

until this LED is off. If the condition persists, have the unit

serviced by qualified personnel.

(Note: This LED will flash when the unit is powered on. This is

normal.)

2. 7-BAND STEREO GRAPHIC
    EQUALIZER SECTION

Содержание SPM 6600/8600
















Отзывы: