1 SPEAKERS:
Connect the respective SPEAKER’s FRONT L, FRONT R,
CENTER, SURROUND LEFT and SURROUND RIGHT channels to their
corresponding loudspeakers. Make sure the “+” (red) terminal and
“ - ” (black) terminal are connected to the corresponding “+” and “ - ”
terminals of the loudspeaker. Use extra care to ensure that no stray
wires or strands cross between posts or terminals at either end.
The VISO FIVE is designed to produce optimum sound quality when
connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 8 ohms minimum per
speaker.
NOTE
Use stranded wire of at least 16 gauge (AWG). Connections to the
VISO FIVE can be made with banana plugs (US model only) or by using
bare wire or pins. Use the transverse hole through the post for bare-wire
or pin connections. By loosening the terminal’s plastic nut, make a
clean, neat connection and re-tighten carefully. To minimize the danger
of short-circuit, ensure that only 1/2-inch of exposed wire or pin is
employed when connecting.
2 12V
TRIGGER
OUT:
The 12V TRIGGER OUT is used for controlling
external equipment that is equipped with a 12V trigger input. This
output will be 12V when the VISO FIVE is ON and 0V when the unit is
either OFF or in standby.
3 CABLE/SAT
&
VCR:
Connect to these inputs S-Video, composite
video, and analog audio from source components such as cable TV
decoders, satellite tuners, another DVD player or other applicable
ancillary devices. VCR may be used with recording components such
as videocassette or DVD-recorders. Connect the VCR OUT (audio/video)
to these components’ corresponding audio/video input. Note that VCR
may freely be used for play-only components, in which case their OUT
jacks would remain unconnected.
4 MONITOR
(S-VIDEO,
VIDEO):
Connect to video input of a monitor/
television using quality dual-RCA and/or S-Video cables designed for
video signals. In general, the S-Video connection is superior and should
be used if your TV/monitor provides the corresponding input.
5 COMPONENT VIDEO IN, COMPONENT VIDEO OUT:
Connect the
Component Video IN to Component Video outputs from compatible
source components, typically a DVD player and terrestrial or satellite HDTV
tuner. Connect Component Video OUT to the Component Video input
of a compatible video monitor/TV. Be sure to observe consistency in
connecting the Y, Cb/Pb, Cr/Pr jacks to the corresponding sources/inputs.
6 SCART/RGB OUT (Euro model/PAL only):
Connect the VISO FIVE’s
“SCART/RGB OUT” to the SCART/RGB video input of a compatible
video monitor/TV. Be sure to observe the correct orientation of the
SCART/RGB plug. Make sure also to set “Video Output” to “RGB” at the
“Disc Video” menu for stable video at SCART/RGB OUT.
7 RESET:
In the unlikely event that the VISO FIVE becomes inoperable or
hangs up, press this button to reset the VISO FIVE.
8 RS-232:
Connect this interface via RS-232 serial cable (not supplied) to any
Windows® compatible PC to allow remote control of the VISO FIVE through
NAD’s proprietary PC software or other compatible external controllers.
NAD is a certified partner of AMX and Crestron and fully supports these
external devices. See your NAD audio specialist for more information.
9 SUBW (SUBWOOFER) PRE OUT:
Connect this output to a powered
(active) subwoofer or to a power amplifier channel driving a passive system.
IDENTIFICATION OF CONTROLS
REAR PANEL
ATTENTION!
Please make sure that the VISO FIVE is powered off or unplugged before making any connections. It is also advisable to power-down or unplug all
associated components while making or breaking any signal or AC power connections.
7
10
11
12 13
14
15
16
17
18
1
4
5
8
9
2
3
6
10
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
Р
У
С
СКИЙ
