background image

LISTENING MODE

    Listening Mode

  }~Stereo

   `Mono

   `Reversed

The C 390DD offers distinct listening modes, tailored for different types 
of recording or program material. The following listening modes can be 
selected.

STEREO
• 

Select “Stereo” when you wish to listen to a stereo production, such as 
music CD or FM broadcast. 

• 

Stereo recordings whether in PCM/digital or analog form and whether 
surround-encoded or not encoded, are reproduced as recorded. 

• 

Multi-channel digital recordings (Dolby Digital and DTS) are reproduced 
in “Stereo Downmix” mode via the left and right speakers only.

MONO
• 

Use “Mono” listening mode when the audio source format is mono. The 
mono information is replicated on both left and right channels. 

• 

Mono” listening mode is recommended when watching old movies 
with mono soundtrack, listening to recorded monaural sound sources 
such as AM radio broadcasts or with the foreign language soundtracks 
recorded in the left and right channels of some movies. 

• 

Mono is also very helpful when setting up a stereo system to check that 
both speakers are connected with correct polarity. Correctly connected 
speakers will have a solid center image and strong bass response. If one 
speaker has the input connections (+ and -) reversed, the image will be 
indistinct and the bass will be reduced and uneven sounding.

REVERSED
• 

Sends the right channel to the left speaker and the left channel to the 
right speaker. This can easily correct a reversed input connection or 
incorrectly recorded music source. 

SPEAKER COMPENSATION

  Speaker Compensation

  `2 ohms

 }~4 ohms

  `5 ohms

  Speaker Compensation

 }`6 ohms

  `7 ohms

  `8 ohms

  Speaker Compensation

 }`>8 ohms

Digital impedance compensation filter allows fine tuning of the top 
octave to match the speaker impedance. This will result in perfectly flat 
frequency response at 20 kHz. The effect of this filter may not be audible* 
but it is measurable, and it compensates for the small effect of the digital 
reconstruction filter that eliminates the 844 kHz sampling frequency of the 
amplifier. 

*The exception may be some electrostatic speakers that have very low 
impedance at high frequency. The lower the HF impedance, the greater the 
deviation from flat response.

PRE OUT/SUBWOOFER

 }Pre Out

  Subwoofer

      Pre Out

 }~Enable

  `Disable

      Subwoofer

  `Enable

 }~Disable

Set the assignment of the rear panel output port PRE OUT/SUBW to either 
PRE OUT or SUBWOOFER. If PRE OUT is selected and enabled, SUBWOOFER 
is automatically disabled and vice-versa.

OPERATION

USING THE C 390DD

16

ENGLISH

FR

ANÇ

AIS

ESP
AÑOL

IT

ALIANO

DEUT

SCH

NEDERL

ANDS

SVENSK

A

РУ

ССКИЙ

Содержание C 390DD

























Отзывы: