Nabco Magnum 4A Control Скачать руководство пользователя страница 18

Страница: 18 / 35

Magnum 4A Control Wiring & Adjustment Manual

www.NabcoEntrances.com

Part #15-10682

Rev. 7-03-14

4-16

Adjustments and Status LEDs

Section 4c. Status LEDs

(2) LED Indicators are used to display what the Magnum 4A Control

is reacting to

at any instant

within the Swing door cycle. This helps to identify when the Swing door system is functioning

properly. Please see Figure 4-4.

Figure 4-4

LED Indicators

DN 0558

Red LED

Green LED

LED

TRANSFORMER

AUX

PWR

TDAS

SIGNAL

INPUT

TDPG

LCHK

Fuse 1: 0.5A 24 VAC

STOP

OPEN

BCHK

Table 4-3

Status LED Indicators

LED

Status

Description

Green

Cycle

Indicates door position during an open and closed cycle.

Indicator

Action

Fast Flashing

(2 flashes per second)

Door is opening.

On Solid

Door is in Back Check.

Slow Flashing

(1 flash per second)

Door is closing.

Off

Door is in Latch Check or Closed

Red

Safety Indicates state of the (2) Safety Signals, or the state of the Current Limit at any instant during the

Swing door cycle.

Indicator

Action

Slow Flashing

(1 flashes per second)

Door mounted Sensor on Swing side of door is activated.

Continuous Safety.

Fast Flashing

(2 flashes per second)

Header Mounted Sensor on Swing side of door is

activated.

Safety with Lockout.

On Solid

Current Limit is activated.

Содержание Magnum 4A Control




































Результаты поиска

Содержание Magnum 4A Control

Отзывы:

Похожие инструкции для Magnum 4A Control

Бренды по названию

Популярные бренды

Nabco Magnum 4A Control, Руководство по монтажу и настройке

Результаты поиска

Содержание Magnum 4A Control

Отзывы:

Похожие инструкции для Magnum 4A Control

Бренды по названию

Популярные бренды