Nabco GT-710 Скачать руководство пользователя страница 5

Страница: 5 / 30

iii

Rev. 9-24-14

Part #15-10683

www.NabcoEntrances.com

GT 710-8710 Swing Door System Low Energy Operator

GENERAL SAFETY RECOMMENDATIONS

Read this “General Safety Recommendations” section before installing, operating

or servicing the automatic door. Failure to follow these practices may result in

serious consequences.

Notice: Read, study and understand the operating instructions contained in, or referenced

in this manual before operating. If you do not understand the instruction, ask the

installing qualified technician to teach you how to use the door.

Do not install, operate or service this product unless you have read and

understand the General Safety Recommendations, Warning Labels, Installation

and Operating Instructions contained in this manual. Failure to do so may result in

bodily injury, or property damage.

Notice: This manual and the owner’s manual must be given to and retained by the

purchasing facility or end user.

►

If the door appears broken or does not seem to work correctly, it should be immediately

removed from service until repairs can be carried out or a qualified service technician is

contacted for corrective action.

►

Disconnect power at the fused disconnect during all electrical or mechanical service.

When uncertain whether power supply is disconnected, always verify using a voltmeter.

►

All electrical troublshooting or service must be performed by qualified electrical

technicians and must comply with all applicable governing agency codes.

►

It is the responsibility of the installing door technician to install all warning and

instructional labels in accordance with ANSI 156.19.

►

It is the responsibility of the purchasing facility or end user to keep warning and

instructional labels and literature legible, intact and with the door.

►

Replacement labels and literature may be obtained from local NABCO Entrances, Inc.

distributors. If the name of the local distrubutor is unknown, contact NABCO Entrances,

Inc. at 1-877-622-2694 for assistance.

Do not place finger or uninsulated tools inside the electrical controller. Touching

wires or other parts inside the enclosure may cause electrical shock, serious

injury or death.

WARNING

DANGER

Содержание GT-710































Результаты поиска

Содержание GT-710

Отзывы:

Бренды по названию

Популярные бренды

Nabco GT-710, Руководство пользователя

Результаты поиска

Содержание GT-710

Отзывы:

Бренды по названию

Популярные бренды