Nabco GT-710 Скачать руководство пользователя страница 26

Страница: 26 / 30

GT 710-8710 Swing Door System Low Energy Operator

www.NabcoEntrances.com

Part #15-10683

Rev. 9-24-14

8-24

Adjustments

CHAPTER 8: ADJUSTMENTS

Section 8a:

LCN Tension Spring

Improperly installed/adjusted Tension Springs may cause property damage or

personal injury. Please follow instructions carefully.

Opening Force must be properly adjusted on the LCN Tension Spring - BEFORE -

the Magnum 4A Control can be adjusted.

8.a.a: Adjust Opening/Closing Force (Manual Mode)

The LCN Tension Spring is used to adjust Opening/Closing Force when the Swing door is used

Manually. The Factory preset force is ideal in most cases. Adjustment should only need to be done in

special cases.

1.►

Turn Power OFF.

2.►

Insert 5/32 Allen Wrench in the Screw located at the end of the LCN Tension Spring. Please see

Figure 8-1

a. The Spring should be adjusted so that the Swing door can be easily pushed open, but still

have enough force to fully close the Swing door.

3.►

To Increase Opening/Closing Force, turn the 5/32 Allen wrench clockwise not more than (9)

full turns.

4.►

To Decrease Opening/Closing Force, turn the 5/32 Allen wrench counterclockwise not more than

(4) full turns.

Figure 8-1

Adjust Door Open Force

DN 0531

5/32” Allen Wrench

LCN Tension Spring

Section 8b: Hydraulic Speed Control

(Automatic Mode)

Note: The Close and Latch Potentiometers located on the Magnum 4A Control is disabled and has no effect.

Figure 8-2

Bottom of Hydraulic Motor

DN 0562

Swing Arm

Hydraulic Speed Controls

The main sprocket may block access to the

main speed hydraulic adjustment valve.

Moving the door slightly open or closed will

align holes in the sprocket with the holes in the

Header allowing access to the valve.

LISTED

501
S

Ma
x

Amp

115 Vo

lts

GYRO

ENTRANCE

NABC

Model No

usage commercial ou industrie

Pedestrian Door Operator

Muskego, WI 53150 USA S82 W18717 Gemini Driv

60 Hz

Commande de porte pietonniere

Pedestrian Commercial & Industri

Manufactur

For Commercial or Industrial Use

BACK CHECK

TCH SPEED

MAIN SPEED

WARNING

CAUTION

Содержание GT-710































Результаты поиска

Содержание GT-710

Отзывы:

Бренды по названию

Популярные бренды

Nabco GT-710, Руководство пользователя

Результаты поиска

Содержание GT-710

Отзывы:

Бренды по названию

Популярные бренды