background image

 

4 of 38

 

GT 300-350-8300-8350 Opus Overhead Concealed Swing Door Installation Manual 

www.NabcoEntrances.com

P/N C-00175 

Rev 5-23-18

CHAPTER 1: WARNING LABELS

Warning labels are universal and used to alert an individual of potential harm to one’s self or to others. The following warning labels are 

listed in a hierarchy order that defines the most potential danger first, and the least potential danger last. Please refer to this page in the 

event that a warning label is displayed within this manual and further definition needs to be explained.

Indicates potentially dangerous situations. Danger is used when there is a hazardous 

situation where there is a 

high

 probability of severe injury or death. It should not be 

considered for property damage unless personal injury risk is present.

Indicates a hazardous situation which has 

some

 probability of severe injury. It should not be 

considered for property damage unless personal injury risk is present.

Indicates a hazardous situation which 

may result in a minor injury

. Caution should not be 

used when there is a possibility of serious injury. Caution should not be considered for 

property damage accidents unless a personal injury risk is present.

Attention:  A situation where material could be damaged or the function impaired .

Notice:     Indicates a statement of company policy as the message relates to the personal safety or protection 

of property. Notice should not be used when there is a hazardous situation or personal risk.

Note: Indicates important information that provides further instruction.

CHAPTER 2: GENERAL SAFETY RECOMMENDATIONS

Do not install, operate or service this product unless you have read and understand the 

General Safety Recommendations, Warning Labels, contained in this manual. Failure to do 

so may result in bodily injury, or property damage.

Read, study and understand the installation and operating instructions contained in, or 

referenced in this manual before operating. If you do not understand the instruction, ask a 

qualified technician. Failure to do so may result in bodily injury, or property damage and will 

nullify all warranties.

Disconnect all power to the junction box prior to making any electrical connections. Failure 

to do so may result in seriouc personal or fatal injury. When uncertain whether power supply 

is disconnected, always verify using a voltmeter.

Do not place finger or uninsulated tools inside the electrical controller. Touching wires or 

other parts inside the enclosure may cause electrical shock, serious injury or death. 

The Ground wire from the Opus Control 120 VAC Harness, and the Incoming 120 VAC 

Ground wire must be connected to the Ground screw located within the Swing door Header.

If the door appears broken or does not seem to work correctly, it should be immediately 

removed from service until repairs can be carried out or a qualified service technician is 

contacted for corrective action.

Notice:     This manual, the owner’s manual and all other associated manuals must be given to and retained 

by the purchasing facility or end user.

Notice:     Wiring must meet all local, state, federal or other governing agency codes.
Notice:     All electrical troublshooting or service must be performed by qualified  

electrical technicians and must comply with all applicable governing  

agency codes.

DANGER

WARNING

CAUTION

WARNING

WARNING

WARNING

WARNING

DANGER

DANGER

CAUTION

CAUTION

Содержание GT 300







































Отзывы: