background image

(Revised 2010-11-15) 

 

DIN-Rail Mounting

 

 
Install the unit in a standard DIN-Rail.  Recess the unit to allow at least 5” of horizontal clearance for fiber optic 
cable bend radius. Note: This unit may be mounted horizontally or vertically. 
 
To install the unit to 35 mm industrial DIN-Rail - Place the top edge of the included mounting bracket on 
the back of the unit against the top flange of the DIN-Rail at a 15° angle. Rotate the bottom of the unit to the 
back (away from you) until it snaps into place. 

     

 
To remove the unit from the 35 mm industrial DIN-Rail - Apply downward force to the unit until it 
disengages from the bottom of the unit from the DIN-Rail. Then, rotate the unit approximately 15° upward 
and towards you to completely remove the unit.
 

Optional Mounting

 

 
With  the  exception  of  the  524TX  and  526FX2,  all  N-Tron™  products  are  designed  to  be  mounted  on 
industry standard 35mm DIN-Rail. However, DIN-Rail mounting may not be suitable for all applications. 
We offer two alternative mounting solutions. 
 
Our  900  Panel  Mount  Assembly  (P/N:  900-PM)  may  be  used  to  securely  mount  our  100,  200,  300,  400, 
500, or 900 Series products to a panel or other flat surface. 

 

 

 
 

Our Universal Rack Mount Kit (P/N: URMK) may be used to mount our products to standard 19" racks. 

 

Содержание 202MC-SC

















Отзывы: