MyTek MWA-105 Скачать руководство пользователя страница 11

Страница: 11 / 54

MyTek

MWA-105 Access Point

Communication Ltd.

Version: 1.1

1.5 Rear Panel Description

Antenna

Power

LAN Reset

Figure 2 – WLAN Access Point Rear Panel

Interfaces

Description

1. Antenna

(Fixed / SMA)

The

Wireless

LAN

Antenna.

2. Power

The power jack allows an external DC +7.5 V power supply

connection.

The external AC to DC adaptor provide adaptive power

requirement to the WLAN Access Point.

3. LAN

The RJ-45 sockets allow LAN connection through Category 5

cables. Support auto-sensing on 10/100M speed and half/ full

duplex; comply with IEEE 802.3/ 802.3u respectively.

4. Reset

Push continually the reset button 5 ~ 10 seconds to reset the

configuration parameters to factory defaults.

MyTek Communication Ltd. Tel: (36-1) 347-0446, (36-1) 280-9397
Vörösmarty utca 79. Budapest Fax: (36-1) 347-0447
Hungary H-1201

http://www.mytek.eu

Содержание MWA-105























































Результаты поиска

Содержание MWA-105

Отзывы:

Бренды по названию

Популярные бренды

MyTek MWA-105, Руководство пользователя

Результаты поиска

Содержание MWA-105

Отзывы:

Бренды по названию

Популярные бренды