Myron L POOLPRO PS9TK Скачать руководство пользователя страница 37

Страница: 37 / 72

and holding the PS9 as prompted, then pressing

caL

prompted.

A hardness value will display when the titration measurement

is complete.

24.

Press

caL.

The “

caL

” icon will display.

25.

Adjust the displayed value to “

200

” using UP or DOWN key. The

PS9 will not allow you to scroll up or down to “

200

” if it is beyond

±10% of the reading. Ref. Total Return to Factory Settings “

Fac

SEL

”, pg. 42 to reset the Hardness Calibration to the “

Fac

”

setting along with all other calibrations.

26.

Press

caL

to accept.

The PS9 will automatically power off after the period of inactivity

defined in the AUTO OFF setting (ref. AUTO OFF, pg. 43).

5. pH Calibration

iMPORTanT:

Always “zero” your P

OOL

with a pH 7 buffer solution

before adjusting the gain with acid or base buffers, i.e., 4 and/or 10,

etc.

a. pH Zero Calibration

Rinse sensor well and cell cup 3 times with 7 buffer solution.

Refill both sensor well and cell cup with 7 buffer solution.

Press

to verify the pH calibration. If the display shows

7.00, skip the pH Zero Calibration and proceed to section b.

pH gain Calibration.

Press

to enter calibration mode. The “

caL

”, “

buFFER

”

and “

” annunciators will appear (see Figure 3). Displayed

value will be the uncalibrated sensor.

nOTE:

If a wrong buffer is added (outside of 6-8 pH), “

”and “

buFFER

”

will flash, and the P

OOL

will not adjust. The uncalibrated pH value

displayed in step 4 will assist in determining the accuracy of the pH

Figure 3

Содержание POOLPRO PS9TK









































































Результаты поиска

Содержание POOLPRO PS9TK

Отзывы:

Бренды по названию

Популярные бренды

Myron L POOLPRO PS9TK, Руководство по эксплуатации

Результаты поиска

Содержание POOLPRO PS9TK

Отзывы:

Бренды по названию

Популярные бренды