manualshive.com logo in svg

MWM Acteon, Руководство по ремонту

Поделиться
Скачать
MWM Acteon Скачать руководство пользователя страница 185

Fuel Injection System

14 - 21

9.612.0.006.7160 - 05/04

After assembling the pump, position the gear on the
shaft and assembly. Once there is not timing on this
gear the pump shaft does not have cotter for
positioning.

Position gear washer and fixation nut and apply the
specified torque.

The protective caps must be removed only
immediately before the piping assembly, avoiding
contaminations.

  Attention

•

The cone of the high pressure pump shaft and the gear must be clean and free of oil

and grease before the fixation. The materials for cleaning can be: test benzene, ethyl

alcohol, glycol or isopropanol.

•

The high-pressure pump, due to its lubrication by the fuel, in any case may work dry.

Before the first start, fill approximately 60 ml of fuel to guarantee the lubrication of the

inner parts. For the first filling, a electric fuel pump can be used with minimum pressure

of 2 bar and 4 bar maximum.

Содержание Acteon
























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды