manualshive.com logo in svg

MWM Acteon, Руководство по ремонту

Поделиться
Скачать
MWM Acteon Скачать руководство пользователя страница 160

13 - 4

Cooling System

9.612.0.006.7160 - 05/04

Thermostat Test Procedure

Test the thermostat and check its operation conditions
according to the procedure below:

•

Place the thermostat in a recipient and fill with

water up the valve stays totally immerse.

•

Position a dial indicator gauge on the stem of the

thermostat and adjust a pre-load of 1 mm.

•

Install a thermometer of scale 0-100 °C immerse

into the water.

•

Gradually heat the water up.

•

Take note of the temperatures at the beginning

and final of the thermostat opening course

(beginning and end of the dial indicator gauge

movement), and the final total course of the dial

indicator gauge (fully open).

•

Compare the values found with the table. Change

the thermostat if the temperature of the beginning

of opening is out of the specified values and / or

the total operation course is below specified.

Check the inspection hole located on the left side of
the engine block (seen by the flywheel side). If there
are signs of water or oil leakage, probably there is
leakage through the water pump or through the sealing
rings. Check and change, if necessary.

Содержание Acteon
























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды