3
NL
TOOLS
M1.1.UCC.NLFREN - 12032018
14. Always turn the heater off after using as leaving it on can cause the
fluid to evaporate and damage the internal components.
15. Upon completion of the cleaning cycle, turn the heater button off
and isolate the machine from the electrical supply.
16. Take care when adding or removing items from the cleaning tank as
the fluid is likely to be hot and displaced fluid can damage the inter
-
nal components. Any displaced fluid must be dried up immediately.
17. In the event of failure/emergency, disconnect the mains supply by
removing the plug from the mains socket.
Operation
1. Fill stainless steel tank with liquid; Plug the cleaner into grounded
outlet; After powering on, the temperature displays the actual solu-
tion temperature.
2. Timer setting: Press the timer control ”UP“ button for setting 1-99
min working time, Press the timer control “DOWN” button for reduc-
ing the time per minute. The cleaning stops when the timer counts
down to 00:00. If the unit needs to be stopped before the timer runs
up, press “ON/OFF” button.
LED display
timer
LED display
heating temp
Temperature
control
Timer control
Heating ON/
OFF
Ultrasonic
ON/OFF
LED display
verwarmingstemperatuur
Temperatuur
controle
Verwarming ON/OFF
Ultrasoon ON/OFF
Timer controle
LED display timer
2.1 Technische gegevens
Model
UCC006
UCC010
UCC020
UCC030
Tankinhoud [l]
6
10
20
30
Ultrasoon vermogen [W]
180
240
480
600
Verwarming vermogen [W]
300
300
800
800
Totaal vermogen [W]
480
540
1280
1400
Afmetingen binnenruimte
(l x b x h) (mm)
270 x 146 x 110
280 x 230 x 120
470 x 226 x 100
470 x 270 x 120
Frequentie [kHz]
40
Temperatuur instelbaar [°C]
20 ~ 80
Timer instelbaar [min.]
1 ~ 99
Totale afmetingen
(l x b x h) [mm]
325 x 180 x 315
330 x 270 x 310
550 x 330 x 310
530 x 525 x 380
Netto gewicht
6,98
10
16
18,2 kg
3 Principe van ultrasoon reinigen
Ultrasoon reiniging is gebaseerd op het cavitatie effect veroorzaakt door het
hoogfrequentie ultrasone golfvibratiesignaal in de vloeistof.
Microscopische bubbels worden gevormd en imploderen heftig, waardoor
cavitatie ontstaat die een intense wrijfactie op het oppervlak van de
voorwerpen veroorzaakt. De bubbels zijn klein genoeg om door kleine ruimtes
te dringen voor een volledige en uniforme reiniging.
Ultrasoon reiniging is uiterst effectief voor het verwijderen van vuil en roet
dat normaal gesproken een langdurige handmatige reiniging zou vereisen.
Deze wordt gebruikt voor de reiniging van allerlei soorten instrumenten en
mechanische onderdelen zoals carburatoren, die bijna nieuw worden zonder
kwetsbare onderdelen te beschadigen.
ULTRASONIC CLEANING PRINCIPLE
Ultrasonic cleaning is based on the cavitation effect caused by high
frequency ultrasonic wave vibration signal in the fluid.
Microscopic bubbles are formed, and they implode violently causing
the cavitation which create an intense scrubbing action on the surface
of the item being cleaned. The bubbles
are small enough to penetrate microscopic
crevices, cleaning hem thoroughly and
consistently.
Ultrasonic cleaning is extremely effective
at removing dirt and grime which would
normally require tedious manual cleaning
by hand. It has been used to clean a wide
variety of instruments and mechanical
parts such as carburetors, returning them
to almost “like new” condition without
damaging delicate parts.
PREPARATION
1. Carefully unpack the cleaner and remove all traces of packing mate-
rials. Visually inspect the cleaner for any parts that may have become
loose or damaged during transit.
Content :
a: Main unit
b: Stainless steel lid
c. Mesh basket
d: Power cord
e: Outlet filter (6L and above models)
f: Instruction manual
Principe van ultrasoon reinigen
Transductor
Generator
Tank
Oplossing
Reinigingsmiddel
Kleine trillingen
Cavitatie
Vuil komt los
copyrighted
document
- all
rights
reserved
by
FBC