background image

VideoEase MonoPro XLR Application Guide 

© MuxLab Inc. 2005-2006                                                                                                 

6

 

Use In Conjunction With Analog Audio Balun (500019) 

The MonoPro XLR also works in conjunction with the 500025 at the source and the 500019 at 
the receiver.  For example, in a building paging system, there may be a central audio distribution 
amplifier with pro-audio balanced (XLR) outputs that needs to connect to remote audio 
amplifiers with line-level (RCA) inputs in another location via Cat5 cable. 
 
However, it is important to note that the nominal professional audio signal is +4dBu and that 
unbalanced line level audio is typically -10dBu.  For example, if one connects the 500025 to the 
500019 via 10 feet of Cat5, the signal level will be too high. 
 
The risks are: 
 

a)

 

the signal may be distorted (s/n ratio) 

b)

 

there will be poor frequency response or  

c)

 

there may be possible damage to the receiver. 

 
In order to ensure reliable operation, the following precautions should be taken: 
 
a) Ensure straight-through polarity between the 500025 and 500019. 
 
b) Ensure that the signal level at the XLR output is not too high and corresponds to -10dBu at 
the receiver either by calculating the signal loss due to the cable and/or adjusting the volume 
controls. 

Содержание VideoEase MonoPro XLR









Отзывы: