MUTOH VJ-628 ValueJet Скачать руководство пользователя страница 57

Страница: 57 / 80

Inside cleaning 57

Cleaning period:

• Monthly

Inside cleaning

Steps

[1]

Check the power is OFF.

[2]

Open the front cover.

Important!

Immediately after turning off the power, the temperature of the heater in this product is very high.
Touch the platen or media guide and if it is too hot, wait for a while before starting cleaning.

[3]

Brush off dusts on the pressure arms with a soft brush.

Important!

• Do not blow off dusts inside the product with a gas duster. It may cause

abnormal noise.

[4]

Using a soft cloth that is soaked in water and squeezed tightly, wipe

dirt on the platen and media guide.

[5]

Using a soft cloth that is soaked in water and squeezed tightly, wipe

dirt on the silver part of grid roller.

[6]

Close the front cover.

Содержание VJ-628 ValueJet

















































































Результаты поиска

Содержание VJ-628 ValueJet

Отзывы:

Бренды по названию

Популярные бренды

MUTOH VJ-628 ValueJet, Руководство по эксплуатации

Результаты поиска

Содержание VJ-628 ValueJet

Отзывы:

Бренды по названию

Популярные бренды