MUTOH VJ-626UF Скачать руководство пользователя

Страница: 87 / 144

Status 3: Job Status 87

Status 3: Job Status

Displays various information of previous print.

Submenus

Displays if the print is completed.

• When the print is completed:

[Completed]

• When the print is canceled: [Canceled]

Displays the total length of print data
(media feeding direction).

Displays the printed length.

Displays the remaining length of print
data.

Note

• The values displayed in this function are just standard values, not guarantee the accuracy.

• If the print data includes no length data, all information will be displayed as “0”.

• This function is to check the information of print data with the print operation is completed. For the details on data while printing, please

refer to the

"What you can do on the operation panel during printing"

"Menu3: Job Status" on page 46

Status 4: Version

Displays the versions of the firmware.

Submenus

Status 5: SerialNo.

Displays the printer’s serial number.

Submenus

Status 3 :

Job Status

JobStatus :

Canceled

ToDoLength :

xxx.x m

Done

xxx.x

Remain

xxx.x

Status 4 :

Version

Version:

Status 5 :

SerialNo.

SerialNo. :

**********

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды