MUTOH VJ-626UF Скачать руководство пользователя

Страница: 44 / 144

44 Pausing / Restarting printing

Pausing / Restarting printing

To halt printing, press the [Cancel] key.

• The printing pauses.

• To resume printing, press the [Enter] key.

Note

• In this operation, printing data sent to the printer are not deleted.

• Please see the followings when canceling printing and deleting data.

"Canceling printing" on page 44

Canceling printing

Press and hold the operation key on the operation panel for two
seconds or more during printing.

• The printing is canceled (it cannot be restarted).

• The printing data sent to the printer are deleted.

Note

You can alternatively do this via the printer driver or the VSM’s remote panel.

What you can do on the operation panel during printing

[1]

Press the [Menu] key while any of the messages on the left is
displayed.

[2]

Use the [+] / [ - ] key to select a menu.

"Menu1: PF Micro Adjustment" on page 45
"Menu2: Backup" on page 45
"Menu3: Job Status" on page 46
"Menu4: Reset Waste Ink" on page 46

Set Media

Remove Media

Media Set

Low speed

Press!

Set Media

Remove Media

Media Set

Low speed

Press!

Printing

Processing

Receiving

Menu1 :

PF Micro Adj.

Menu2 :

Backup

Menu3 :

Job Status

Menu4 :

ResetWasteInk

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды