MUTOH VJ-626UF Скачать руководство пользователя

Страница: 46 / 144

46 What you can do on the operation panel during printing

This menu displays data on the job being printed.

• See the following related sections of Panel Setting Menus (Chapter 2 below):

"Status 3: Job Status" on page 87

Use this menu to reset the waste ink counter to zero, if you empty out the waste ink tank during printing.

• See the following related sections of Panel Setting Menus (Chapter 2 below):

"Mnt. 2: ResetWasteInk" on page 82

Menu3: Job Status

[1]

Press the [Enter] key to access the menu.

[2]

Use the [+] / [ - ] key to select a menu.

• ToDoLength: display this to check the total length (paper feed

direction) of the job being printed.

• Done: display this to check how much of the current job has been

printed.

• Remain: display this to check how much of the current job remains

to be printed.

• Remain time: displays the time remaining to complete the print job.

Note

• The values displayed by this function are approximate. They are not guaranteed to be rigorously accurate.

• If the print job data contains no length information, “0” will be displayed for all these items.

Menu4: Reset Waste Ink

[1]

Press the [Enter] key to access the menu.

[2]

Press the [Enter] key.

The counter will be reset to zero.

Menu3:

Job

Status

ToDoLength:

xxx.x

Done:

xxx.x

Remain: xxx.x

Remain

Time:

xxxx

min

Menu4:

ResetWasteInk

Initial. Parameter?

** Initializing **

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды