MUTOH VJ-626UF Скачать руководство пользователя

Страница: 85 / 144

Mnt. 7: Moving Printer 85

Mnt. 7: Moving Printer

Before packing printer for moving or transporting, use this menu to
automatically move the table to the position to secure the table with shipping
brackets.

"Changing Table Position for Packing" on page 124

Mnt. 8: Table Maint.

Use this menu to automatically move the table to the position to perform the
table maintenance.

"Table Maintenance" on page 113

Mnt. 9: Daily Maint.

Use this menu in following cases:

• If the nozzle missing still persists after performing head cleaning.

• If you perform printing all day without entering to sleep mode and you need

to perform daily maintenance.

"Clean daily maintenance parts" on page 109

Submenus

Press the [Enter] key to start maintenance.

After the maintenance is complete, press
the [Enter] key.

• The printer automatically performs the

Short cleaning.

Important!

To perform daily maintenance after using the printer for the day, see

"Daily Maintenance" on page 99

Mnt. 7 :

Moving Printer

Mnt. 8 :

Table Maint.

Mnt. 9 :

Daily Maint.

Daily Maint. :

Start

Daily Maint. :

End

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды