MUTOH VJ-626UF Скачать руководство пользователя | Manualshive

Страница: 123 / 144

background image

Transporting the printer 123

When transporting this printer, it is necessary to empty the waste ink tank. and fixate the print head and the table with
packaging material. If transported without these steps, it can cause ink leakage and damage to the print head.

To use the printer again, reinstall the printer and perform initial charging.

Transporting the printer

1.

Discharging the ink in the printer and waste ink

[1]

Press the [Menu] key.

[2]

• Press the [ - ] key until “Menu 3: Maintenance >” appears.

• Press the [>] key.

[3]

• Press the [ - ] key until “Mnt.5: Ink Discharge” appears.

• Press the [Enter] key.

[4]

Press the [Enter] key.

[5]

When the message on the left appears, transfer the waste fluid into a
container.

"Drain waste fluid into container" on page 97

waste ink tank"

[6]

• Press the [Enter] key.

• The message on the left will appear.

[7]

Remove the cartridges from all the cartridge slots.

The message on the left will appear.

• Discharging the ink will start.

[8]

When the message on the left appears, transfer the waste fluid into a
container.

"Drain waste fluid into container" on page 97

waste ink tank"

[9]

Reset the waste ink counter.

"Resetting waste ink counter" on page 98

1

2

Set Media

Remove Media

Media Set

Low speed

Press!

Menu 3 :

Maintenance >

Mnt.5

:

Ink

Discharge

Ink Discharge :

Start

Empty WasteInk

- > E

Remove Cartridges

During discharge

**%

No Cartridge

[123456] No

Cartridge

«
...
121
122
123
124
125
...
»

Содержание VJ-626UF

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для VJ-626UF

Бренд: Olivetti Страницы: 78

Бренд: Stratasys Страницы: 68

Nuvera 100 roduction Systems

Бренд: Xerox Страницы: 70

LaserMatrix LM2405

Бренд: Output Technology Страницы: 249

1235N - Phaser Color Laser Printer

Бренд: Tektronix Страницы: 240

Бренд: L-Mark Страницы: 62

5700i - EPL B/W Laser Printer

Бренд: Epson Страницы: 33

2180 - LQ B/W Dot-matrix Printer

Бренд: Epson Страницы: 2

2190 - FX B/W Dot-matrix Printer

Бренд: Epson Страницы: 2

2200 - Stylus Photo Color Inkjet Printer

Бренд: Epson Страницы: 62

24-PIN DOT MATRIX PRINTER LQ-680PRO

Бренд: Epson Страницы: 3

Бренд: Epson Страницы: 2

2190 - FX B/W Dot-matrix Printer

Бренд: Epson Страницы: 48

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 106

50 - Artisan 50 - Printer

Бренд: Epson Страницы: 2

24-PIN DOT MATRIX PRINTER LQ-680

Бренд: Epson Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды