MUTOH VJ-1638UH Mark II, Руководство по установке

Страница: 7 / 16

7 VJ1638UH2E-I-02
VJ-1638UH Mark
Ⅱ
INSTALLATION MANUAL
1
2
1
1
2
2
1
1
1
2
1
CAUTION
1. Make sure that the printer is turned OFF.
2. Connect the power cable to the AC inlet on the
rear side of the product.
5 Power cable connection
This section explains power cable connection.
Follow the procedure below to install the power cable.
Be sure to use the power cable supplied
with the printer.Using other power cables
can cause an electric shock or fire.
Use the power cord set compliant with the
safety standards, power-supply voltage,
and plug shape of the country where the
printer is used.
Use a power cord set which is equipped
with a protective earth, and securely
connect it to the outlet.
Do not use a damaged power cable.
It could lead to an electric shock and fire.
Do not pull out or insert the power plug
with a wet hand.
This could lead to an electric shock.
Make sure to use only the specified power
supply (AC 100 - 120 V or AC 200 - 240
V). If a power supply other than the
specified voltage is used, it could cause
an electric shock and fire.
Take power for the printer directly from
the power socket (AC 100 - 120 V or AC
200 - 240 V).Do not use multiple plugs on
the same socket.This could generate heat
and might cause fire.
Be sure to use a dedicated power socket
with earth wire for the power supply, and
connect it to the earth wire.
If the earth wire is not connected, an
electric shock or fire may occur.
Do not connect an earth wire to the
following places.
Pay attention to the following points when
handling the power supply plug.
Any mishandling of the power cable could
cause a fire.
Make sure that no foreign substances
such as dust etc. are stuck to the power
plug.
Make sure that the power plug is firmly
inserted to the edge of the power socket.
Make sure to connect an earth wire to the
earth connection that meets the following
standards.
Earth terminal of power socket
Earth wire with copper plate which is
buried at 650 mm or more, deep in the
ground.
Contact the retail outlet of purchase if the
earth connection cannot be established,
or if the earth connection is not given.
When the power supply of the printer is
ON, do not pull out the power cable from
the power socket. Whenever the plug is
pulled out from the power socket, allow
one minute or more before inserting the
plug in the power socket again.
Gas pipe
There is a possibility of ignition and
explosion.
Earth wire of telephone cables and
lightning rods
Heavy current might flow whenever
lightning strikes.
Water pipe and faucet
The earth might not work if a plastic
pipe is connected in the middle of the
metal pipe.
Pay attention to the following points when
handling power cable.
Contact your local MUTOH dealer in case of
power cable damage.
This product is also designed for IT power
distribution system with phase-to-phase
voltage 230V.
The power is ON when the [Power] key of
the operation panel is pressed in.
Press the key once again to turn OFF the
power.
Do not tamper with the power cable.
Do not put heavy objects on the power
cable.
Do not bend, twist or pull the power
cable by force.
Do not route the power cable near
heating appliances.
5. Place the level at the edge of printer’s platen, and
check the position of the air bubble.
6. Place the level on the frame of media-feed table.
Place the level on the same side as when you
placed it on the printer.
7. Turn the screw of media-feed table’s caster (the
one further from the printer) with a spanner, and
adjust the slant.
Make sure that the position of the level’s air bubble
is at the same position as when you place it on the
printer.
8. Adjust the slant on the other side in the same way.
Caster of media-feed table has 2 types of
screws. Turn the bottom screw.
Turn the screw clockwise to raise
Media-feed table.
2
6mm
4. Turn the screws on the caster of media-feed table
(2 places, ones closer to the printer) with a spanner.
Adjust so that there is a 6 mm gap between the top
side of the square hole of Paper guide F and the top
side of the positioning guide.
Name No. Name No.
Screws on Caster
1
Positioning guide
2
Name No. Name No.
Level
1
Platen
2
Name No. Name No.
Screws on Caster
1
Level
2
Name No. Name No.
AC inlet
1
Power Cable
2
Name
No.
Name No.
Frame of media-feed table 1 Level 2
NOTE
WARNING
CAUTION
1 2
NOTE
NOTE
WARNING
CAUTION