MUTOH ROCKHOPPER 48 inch Скачать руководство пользователя страница 35

Preparing for a job 

Operation Instructions Rockhopper Printer

 

 

Page 

35

 

AP-75024 Rev. 1.2. – 18/08/2002 

 

PREPARING FOR A JOB 

INSTALLING THE INK CASSETTES 

 

PRECAUTIONS WHEN USING INK CASSETTES :

 

Please read below recommendations carefully before you start using your Rockhopper ink 
cassettes. 

 

Caution: 

  It is recommended to avoid any direct contact with the inks.  If you 

come in close contact with the inks, please pay attention to the 
following first-aid measures: 

Eye contact: Rinse out the ink with a large quantity of water and 
consult your doctor. 
Skin contact: Wash off the ink with soap and water. 
Ingestion: Rinse your mouth immediately, drink a large quantity of 
water or milk and consult your doctor. 

  Keep the ink cassettes out of the reach of children. 

  The ink cassettes are inflammable (ignition point 63°C).  Avoid contact 

with heating sources and any sort of ignition source. 

 

 

Important: 

  If you use your Rockhopper printer for the first time, you need to 

install 6 cassettes in the slot, which is located at the back of the 
printer. 

  Before using Eco-Solvent ink, perform a head wash.  Tubes, heads 

and filters must be clean.  Use the special Eco-solvent Transition 
Liquid. 

  Once you have worked with eco-solvent inks, it is forbidden to change 

to another ink type. 

  Do not use other ink cassettes but the exclusive Mutoh Rockhopper 

ink cassettes.  When using non Mutoh ink cassettes, the ink supply 
system, the heads as well as the cleaning system will be considered 
out of warranty if damage occurs.  Also see to it that you install your 
cassettes in the correct way.  Use of incorrectly coded cassettes may 
cause printer damage. 

 

Содержание ROCKHOPPER 48 inch















































































Отзывы: