manualshive.com logo in svg

Murray 425002x99A, Инструкция, Страница: 30 / 52

Поделиться
Скачать
Murray 425002x99A Скачать руководство пользователя страница 30

MAINTENANCE

30

F–030726L

INSTALLATION

1. Slide the 

motion drive belt

 between the 

stack pulley

 and the

belt guides 

(Figure 33). Install the 

motion drive belt

 on the

top pulley of the 

stack pulley

. Make sure the “V” side of the belt

is against the pulley.

2. Push the 

motion drive belt

 through the opening between the

steering plate and the engine plate.

3. Install the end of the 

motion drive belt

 around the 

drive pulley

(Figure 30).     

4. Tighten the 

belt guides

 at the 

drive pulley

 (Figure 31).

5. Put the belt around the 

idler pulley 

(Figure 30, Figure 35).

Assemble the 

idler pulley

. Fasten the 

idler pulley

 with the hex

nut. Make sure the flat side of the belt is against the 

idler pulley

.

Also, make sure the belt is not twisted.

6. Make sure the 

motion drive belt

 is inside all the 

belt guides

(Figure 30, Figure 31).

7. Attach the 

adjuster nut

 and 

shift link

 to the 

adjuster bracket

with a 

hair pin

 (Figure 32). See “How To Adjust The Shift

Lever”.

8. Attach the 

steering shaft assembly

 to the steering plate with

two screws (Figure 34).

9. Attach the 

access panel 

(Figure 34).

10. Check the routing of the motion drive belt. Make sure the

motion drive belt

 is installed correctly on the 

idler pulley

.

Make sure the 

steering shaft assembly

 in inside the 

motion

drive belt

 (Figure 35).

11. Install the battery.

12. Before you use the unit, check the adjustment of the clutch. See

the instructions “How To Check And Adjust The Clutch”.

13. Install the mower housing. See the instructions “How To Install

The Mower Housing”.

Figure 35

Motion Drive

Belt

Idler Pulley

Stack Pulley

Steering Shaft

Assembly

Содержание 425002x99A





















































Отзывы:

Нет отзывов