manualshive.com logo in svg

Murray 425002x99A, Инструкция, Страница: 11 / 52

Поделиться
Скачать
Murray 425002x99A Скачать руководство пользователя страница 11

ASSEMBLY

11

F–030726L

HOW TO INSTALL THE SEAT

Use the fasteners shown below to install the 

seat

. The fasteners are

shown at full size.

 

(A)

1001054

(B)

17x47

1. Carefully remove the plastic bag from the 

seat.

2. Align the holes in the 

seat hinge

 to the holes in the 

seat

(Figure 1). Fasten the 

seat

 to the 

seat hinge

 with the fasteners

as shown.

3. Check the operating position of the 

seat.

 If the 

seat

 needs to

be adjusted, loosen the two 

wing bolts

. Slide the 

seat 

forward

or backward along the 

seat adjusting holes

 as shown. Tighten

the 

wing bolts (A).

Figure 1

Seat

Seat 

Adjusting Hole

Seat Hinge

A

B

HOW TO ASSEMBLE THE STEERING WHEEL

Fasteners are not required to assemble the steering wheel. Attach

the steering wheel as follows:
1. Make sure the front wheels point forward.
2. Look at the

 hub 

of the 

steering wheel

. Make sure the locking

clip is in place inside the 

hub

.

3. Slide the 

cover

 over the 

steering post 

(Figure 2).

4. Slide the 

steering wheel 

onto the 

steering post.

 Push on the

steering wheel

. The steering wheel will lock onto the steering

post. Pull on the steering wheel. Make sure the steering wheel

is locked in place.

5. Some models have an 

decal

 in the parts bag. Attach the

 decal

to the center of the

 steering wheel 

as shown.

Steering Wheel

Steering Post

Cover

Decal  (Optional)

Figure 2

Hub

HOW TO ASSEMBLE THE GAUGE WHEELS

Use the fasteners shown below to install the 

gauge wheels

. The

fasteners are shown at full size.

(A)

31x11

(B)

17x91

1. Attach the 

gauge wheels

 to the 

axle bolts

 with the fasteners.

NOTE: The axle bolt is mounted in the LOW position. To change

the position to a higher cutting position, see “How To Adjust

The Gauge Wheels” in the Maintenance section.

Gauge Wheel

Figure 3

Axle Bolt

A

B

Содержание 425002x99A





















































Отзывы:

Нет отзывов