IMPORTANT:
1. Water supply is 3/8” Outside Diameter Copper Tube. Waste is 1-1/4” Outside Diameter.
2. Completely flush supply lines of all foreign debris before connecting to fixture. Drinking Fountain designed to not
affect taste, odor, color, or sediment. Optional water filter (WF1) is available should any of these problems arise
from the water supply.
3. Do NOT solder Copper Tube when inserted into the Coupler as damage to the O-Ring will result.
4. All burrs must be removed from outside of cut tubes before inserting into Coupler or other components.
5
. WARNING: Warranty is voided if installatio
n is not made following current Murdock Mfg. installation instructions
and if components are assembled to the fixture that is not approved by Murdock Mfg.
6. Fixture operates within water pressure range of 20 to 105 PSIG (138 to 724 kPa). Murdock Mfg. will not warranty
fixtures damaged when connected to supply lines with flow pressure lower than 20 PSIG (138 kPa) or higher than
105 PSIG (724 kPa). A pressure regulator must be furnished by others on supply line if inlet pressure is greater
than 105 PSIG (724 kPa).
7.
Per UPC 609.10
-
All building water supply systems in which quick acting valves are installed shall be provided with
devices to absorb the hammer caused by high pressure resulting from the quick closing of the valve. These
pressure-absorbing devices shall be approved mechanical devices. Water pressure-absorbing devices will be
installed as close as possible to the quick closing valve.
INSTALLATION:
1. Mount Hanger Bracket to wall horizontally level as shown in Roughing-In and Dimensional Drawing. Note: Adjust
height of bracket if Bubbler outlet height is required to vary from that shown.
WARNING: Hanger Bracket MUST be securely anchored to wall with fasteners sufficient to support 3 times the
weight of Drinking Fountain. If wall can not provide adequate support, order and install optional fixture support
carrier.
2. Remove the Bottom Cover from the Drinking Fountain and set aside in a safe place. Save the Screws in a secure
location for re-use in later stages of installation.
3.
START UP:
1. Before connecting water supply and assembling Bottom Cover to Drinking Fountain, but after thoroughly flushing
the supply line and connecting it to the fixture, turn on building water supply and check all connections for leaks.
2. Air within the Drinking Fountain system or the structure supply piping will cause an irregular Bubbler outlet stream
until purged out by incoming water. Covering the Bubbler with a clean cup (or similar object) is recommended when
first activating Drinking Fountain to prevent excessive splashing. Depress the Pushbutton until steady water stream
is achieved.
3. If water flow requires adjustment, insert a Slotted Narrow Blade Screwdriver in the hole centered on the underside
of the fixture in the knee clearance area up to the Flow Regulator. Turning clockwise will increase flow and turning
counterclockwise will decrease flow.
4. Recheck all water and drain connections with water flowing through system.
5. Assemble Bottom Cover to Drinking Fountain with Screws furnished.
Hang the Drinking Fountain on the Hanger Brackets ensuring the Bracket Tabs engage AND seat in the slots in the
back of the Drinking Fountain. Verify Drinking Fountain are level, left to right AND front to back from bottom of unit.
NOTE: The Bubbler stream may be adversely affected if units are not square and level. Bottom of units and
Louvers should be used as reference to verify unit is square and plumb.
4. Anchor the Drinking Fountain to the wall at the lower mounting points in each Back Panel. Shim lower mounting
points to level unit if necessary.
5. Thoroughly flush the 3/8” O.D. supply line and then connect Drinking Fountain to Water Supply Angle Stop Valve (by
others) with supplied 3/8” O.D. Copper Tube.
6. Use supplied Flexible Hose and Clamps to connect Waste Tailpiece from the upper unit to the Waste Tailpiece of
lower unit and then make up 1-1/4” O.D. P-Trap Waste Connection. Waste P-Trap by others.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A172-SO
Page 3 of 10
Revised:
12/20/17
7020-961-001
MURDOCK MFG. •
15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com
Member of
