background image

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

 

A152-BF4-FRA

Page 11 of 18

NEW

7020-945-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

CLEANING & MAINTENANCE GUIDE:

1.

Motors have lifetime lubrication and do not require scheduled maintenance.

2.

Excess dirt or poor ventilation will cause the compressor overload protector to turn the compressor off and it 

will cycle on and off with no cold water coming out of bubbler. Periodically clean with vacuum cleaner, air 
hose or brush the condenser fins and cabinet ventilation louvers. In environments where dirt and dust is 
more prevalent, clean more frequently.

3.

Periodically remove fountain top and clean out in-line strainer.

4.

Periodically remove access panel of cooler and clean out inline “Y’’ strainer

For Powder coated units:

 Units should be cleaned using a mild soap solution with a sponge or cotton cloth. 

Wipe down surfaces then rinse with clean water.

For Stainless steel units:

1.

To Remove water spots or rust spots, stainless steel cleaner/polish on a cloth is
recommended.

2. 

If there are stubborn spots or if you wish to treat a scratch, synthetic abrasive general
purpose pads such as  scotch brite are recommended.

3. 

Stainless steel should be kept clean at all times. If a coating of stainless steel cleaner/ 

polish is maintained, stainless steel surfaces will retain their new, clean, polished 
appearance indefinitely.

Содержание A152-BF4-FRA Series



















Отзывы: