manualshive.com logo in svg

Munters WM54K, Инструкция по эксплуатации, Страница: 31 / 36

Поделиться
Скачать
Munters WM54K Скачать руководство пользователя страница 31

31

© Munters Corporation, September 2019

QM1078r1

Provide Weather Shel-
ter Over Fans

6" Min.

Fan with
Discharge Cone

Figure 32

Snow Guards located 
per manufacturers 
recommendations*

Ceiling

Figure 33

Winterizing

6.

Fan with
Discharge 
Cone

Note:

 

Snow guards are designed to prevent sudden, dangerous snow 

and ice slides when attached to the building roof according to 
manufacturers recommendations. The supplier listing above is given 
as a reference only.  Munters does not endorse any specific snow 
guard product and no performance warranty is implied.

 

Munters Product and System 

Warranties do not cover cone or fan 

damage from external sources.

IMPORTANT

!

Snojax, Inc. 

800-766-5291 

717-697-2452 

www.snojax.com

Polar Blox 

800-298-4328 

814 629-9090 

www.polarblox.com

LM Curbs 

800-284-1412 

903 759-3598 

www.lmcurbs.com

Alpine Snow Guards 

888-766-4273 

888-766-9994 

www.alpinesnowguards.com

*Snow Guard Suppliers

 

Company Name 

Phone No. 

Fax No. 

Web Site

 

In most climates, it is probable that the ventilation system will never need to operate at a total capacity 
during the colder winter months. Consequently, it is advisable to “winterize” those fans which will not 
be used in cold weather to avoid unnecessary heat loss and condensation.

To winterize, turn fan control “off”. Install the insulated closure panel over the fan intake. If you don’t 

have an insulated closure panel, a piece of rigid insulation material can be used. Remember the 
insulation panel must be removed before warmer weather returns.

NOTE:

  At least one single speed fan should be left uncovered and with power available to provide air     

     movement in the event of variable speed control difficulties.

6.1 Winterizing

6.2 Winter weather protection

To prevent cone or fan damage from snow or ice sliding off building roof, weather protection must be 
provided. A weather shelter may be constructed to cover the entire fan, 

See Figure 32,

 or snow guards 

may be placed on the roof, 

See Figure 33.

Building
Wall

Содержание WM54K





































Отзывы:

Нет отзывов