manualshive.com logo in svg

Munters WM54K, Инструкция по эксплуатации, Страница: 23 / 36

Поделиться
Скачать
Munters WM54K Скачать руководство пользователя страница 23

23

© Munters Corporation, September 2019

QM1078r1

Step 27
 

Use a straight edge or level to check alignment of Propeller Sheave, 
Tensioner Pulley and Motor Sheave.  If needed, adjust position of Motor 
Sheave so the 3 pulleys line up.  Once Motor Sheave is aligned tighten 
the set screw to 75 in-lbs [9 N-m] torque.  

See Figure 27.

Installation Instructions

Chapter 2

Propeller Sheave

Figure 27

Tensioner Pulley

Motor Sheave

Level

Step 28A
 

Slide V-belt over Propeller and install by wrapping 
it around 2 smaller pulleys and starting it over 
larger Sheave.  Continue rolling it onto the larger 
Sheave until it fits into groove. 

 See Figure 28A. 

 

If desired the 2 drain holes in the Orifice Panel 
can be plugged using (2) Hole Plugs [KK].

Figure 28A

Step 26B
 

Using channel locks and/or a hammer twist the motor bracket stiffener so that the holes in the bracket lay flat 
against the framing.  Then attach bracket to framing using (1) Lag Screw [LL].  

See Figure 26B.

Figure 26B

Frame

Stiffener

Lag Screw [LL]

Drain Holes

Содержание WM54K





































Отзывы:

Нет отзывов