background image

ComDry Control System

1.15 Service interval alarm

The Service interval [T-xxxx h] can be set between 500 and 8.000 hours.

To reset counters you must have “one-star” access. Follow these steps to change the service interval (see also

1.11, Change the system settings

):

Step

Action

Result / Illustration

1

Go to the Time menu.

2

Navigate to "Service interval" [T-xxxx h]

2

Adjust the "Service interval" [T-xxxx h] in steps of 100 hours

3

Reset the "Time to service" counter [S xxxx h].

NOTE!

The "Time to service" counter can be reset at any time. When the counter is reset, it starts counting up or

down again from the pre-set value [T-xxxx h] depending on how the "Service interval" has been adjusted.

The Time to service counter [S xxxx h] counts down to zero. When it reaches zero, the system issues a "soft
alarm" the next time the unit is switched on. The alarm only makes the alarm menu symbol flash, not the
red alarm indicator, and [TIME FOR SERVICE] is shown in the display. The alarm will not make the unit
stop. The unit can still be operated as normal with the alarm present.

Follow these steps to check the service parameters and stop the service alarm:

Step

Action

Result / Illustration

1

To see or check parameters, either reset the alarm by pressing

and reset it, or leave the Alarm menu with [EXIT].

2

To stop the alarm completely, navigate to the "Time to service"
counter [S 0000] in this menu and reset it.

NOTE!

Even if the alarm has been reset in the Alarm menu, it will be re-issued the next time the unit is switched

on.

See the User manual for proper maintenance action.

MEN-CDCS-A1808

Operation

9

Содержание ComDry





















Отзывы: