Multitech Zpx Multimodem MT5634ZPX-PCI-V92 Скачать руководство пользователя страница 16

Страница: 16 / 85

2 Installation

MultiModemZPX User Guide

Windows NT 4.0

Before you begin a Windows NT installation, make sure Windows NT Service Pack 3
or newer is installed on the computer. Also, to add and remove devices you must be
logged on with Administrator privileges.

1. After installing the MultiModemZPX modem into your computer, turn the com-

puter on and allow Windows NT to start.

2. Insert the MultiModemZPX CD into your computer’s CD-ROM drive.

3. When the

MT5634ZPX-PCI Autorun

menu appears, choose

Windows NT Setup

4. The

Multi-Tech Systems NT4 PCI Modem Setup

dialog box shows the COM

port assigned to the modem. You can change the COM port assignment by click-
ing the down arrow and selecting an unused COM port.

5. Now click

Install

. The MT5634ZPX-PCI-V92 driver is installed on the selected

COM port.

6. When a message asking you to restart the computer appears, remove the CD

from the CD-ROM drive, and then click

to restart the computer.

Remote Access Setup

Before you can use your modem, Dial-Up Networking must be installed, and the
new modem must be selected as the Remote Access Service device.

If Dial-Up Networking is not installed

1. Double-click the My Computer icon, and then double-click the Dial-Up Net-

working icon. If Dial-Up Networking is not installed, you will see an

Install

button in the

Dial-Up Networking

dialog box.

2. Insert the Windows NT 4.0 compact disc into the CD-ROM drive.

3. Click

Install

in the

Dial-Up Networking

dialog box.

4. In the

Add RAS Device

dialog box, choose

Multi-Tech Systems MT5634ZPX-

PCI-V92

, and then click

5. In the

Remote Access Setup

dialog box, click

Configure

Содержание Zpx Multimodem MT5634ZPX-PCI-V92






















































































Результаты поиска

Содержание Zpx Multimodem MT5634ZPX-PCI-V92

Отзывы:

Похожие инструкции для Zpx Multimodem MT5634ZPX-PCI-V92

Бренды по названию

Популярные бренды

Multitech Zpx Multimodem MT5634ZPX-PCI-V92, Руководство пользователя

Результаты поиска

Содержание Zpx Multimodem MT5634ZPX-PCI-V92

Отзывы:

Похожие инструкции для Zpx Multimodem MT5634ZPX-PCI-V92

Бренды по названию

Популярные бренды